Zenoah G2000T ユーザーズマニュアル
G2000T
GB-15
G
B
9. Troubleshooting Guide
Case 1. Starting failure
Make sure the icing prevention system is not working.
Check fuel for water
or substandard mix-
ture.
or substandard mix-
ture.
Replace with proper
fuel.
fuel.
Check for engine
flooding.
flooding.
Check spark ignition.
Remove and dry the
spark plug.
Then pull the starter
again with no choke.
spark plug.
Then pull the starter
again with no choke.
Replace with a new
plug.
plug.
Case 2. Lack of power/Poor acceleration/
Rough idling
Case 3. Oil does not come out
Check fuel for water
or substandard mix-
ture.
or substandard mix-
ture.
Check air filter and
fuel filter for clog-
ging.
fuel filter for clog-
ging.
Check carburetor
for inadequate ad-
justment.
for inadequate ad-
justment.
If the unit seems to need further service, please consult
with an authorized service shop in your area.
with an authorized service shop in your area.
Replace with proper
fuel.
fuel.
Clean.
Readjust speed
needles.
needles.
Check oil for sub-
standard quality.
standard quality.
Check oil passage
and ports for clog-
ging.
and ports for clog-
ging.
Replace.
Clean.
a
d
d
a
a
d
d
a
a
a
d
a
a
10. Disposal
When disposing your machine, fuel or oil for the machine,
be sure to allow your local regulations.
be sure to allow your local regulations.
WARNING
11. Specifications
Power unit:
Displacement (cm
3
): ............................................. 18.3
Fuel: ................ Mixture (Gasoline 50 : Two-cycle oil 1)
(when using ZENOAH genuine oil)
Fuel tank capacity (cm
(when using ZENOAH genuine oil)
Fuel tank capacity (cm
3
): ....................................... 170
Chain oil: ................................. Motor oil SAE# 10W-30
Oil tank capacity (cm
Oil tank capacity (cm
3
): .......................................... 160
Carburetor: ........................... Diaphragm type (Walbro)
lgnition system: ..................................... Pointless (CDl)
Spark plug: .............................................. NGK CMR7A
Oil feeding system: ...... Automatic pump with adjuster
Power .......................................... 0.64/9,000 (kw/min
lgnition system: ..................................... Pointless (CDl)
Spark plug: .............................................. NGK CMR7A
Oil feeding system: ...... Automatic pump with adjuster
Power .......................................... 0.64/9,000 (kw/min
-1
)
Max speed ............................................. 12,500 (min
-1
)
Idle speed ................................................ 2,900 (min
-1
)
Dimensions (L x W x H) (mm): ............ 270 x 190 x 190
Dry weight
Power unit only (kg): ............................................... 2.2
Dry weight
Power unit only (kg): ............................................... 2.2
Cutting head:
Sprocket (Teeth x Pitch): .................................. 8T x 1/4
Guide bar
Type: ................................................ Sprocket nose
Size (in. (mm)): ............................................. 8 (200)
Saw chain
Type: .................................................. Oregon 25AP
Pitch (in. (mm)): ........................................ 1/4 (6.35)
Gauge (in. (mm)): ................................... 0.05 (1.27)
Guide bar
Type: ................................................ Sprocket nose
Size (in. (mm)): ............................................. 8 (200)
Saw chain
Type: .................................................. Oregon 25AP
Pitch (in. (mm)): ........................................ 1/4 (6.35)
Gauge (in. (mm)): ................................... 0.05 (1.27)
Specifications are subject to change wihout notice.