Land Pride RCR1260 ユーザーズマニュアル
9
Section 1: Assembly & Set-up
12/15/15
RCR1248, RCR1260 and RCR1272 Rotary Cutter 326-047M
7.
Insert properly sized linchpins (#18) in hitch pins
(#20). (Customer to supply properly sized linchpins.)
(#20). (Customer to supply properly sized linchpins.)
8.
RCR1272 tailwheel A-frame (#3) is shipped
unattached. Attach A-frame as follows:
unattached. Attach A-frame as follows:
a. Attach front end of A-frame (#3) to the deck as
shown with 5/8"-11 x 1 3/4" GR5 bolts (#8). Do not
install hex flange lock nuts (#14) at this time.
install hex flange lock nuts (#14) at this time.
b. Attach back end of A-frame (#3) as shown to
adjusting plate with 3/8"-16 x 1 1/4" GR5 carriage
bolts (#10) and hex whiz nuts (#13). Tighten hex
whiz nuts to the correct torque.
bolts (#10) and hex whiz nuts (#13). Tighten hex
whiz nuts to the correct torque.
9.
If RCR1248 or RCR1260, remove hex flange lock
nuts (#14) from bolts (#8). Do not remove bolts.
nuts (#14) from bolts (#8). Do not remove bolts.
10. Attach rear braces (#5) inside of tailwheel main
frame (#3) with 5/8"-11 x1 3/4" GR5 bolts (#8) and
secure with hex flange lock nuts (#14). Draw lock
nuts (#14) up snug and then back off 1/4 turn.
secure with hex flange lock nuts (#14). Draw lock
nuts (#14) up snug and then back off 1/4 turn.
11. Rotate A-frame/floating top hitch (#6 & #24) up and
rotate left rear brace (#5) up as follows:
IMPORTANT: See Detail A in Figure 1-2 on page 9
Floating top hitch (#24) must be installed with ears
(#25) above rear brace bars (#5).
Floating top hitch (#24) must be installed with ears
(#25) above rear brace bars (#5).
Hitch & Tailwheel Assembly
Figure 1-2
30289
IMPORTANT: Some small tractors with a Cat. I 3-point hitch cannot lift
cutter high enough for transporting or is not heavy enough in the front to
properly lift the cutter. If your are experiencing this problem, attach A-frame
bars (#6) and hitch pins (#20) in lower 3-point mounting holes “B”.
cutter high enough for transporting or is not heavy enough in the front to
properly lift the cutter. If your are experiencing this problem, attach A-frame
bars (#6) and hitch pins (#20) in lower 3-point mounting holes “B”.
a. Refer to Detail A: If attaching cutter to a 3-point
Cat. I hitch, align holes A in rear braces (#5) with
hole in floating top hitch (#24).
hole in floating top hitch (#24).
b. Refer to Detail A: If tractor is too small to lift cutter
high enough for transporting, align hole B in rear
braces (#5) with hole in floating top hitch (#24).
braces (#5) with hole in floating top hitch (#24).
12. Insert 3/4"-10 x 4" GR5 bolt (#9) into the left rear
brace (#5), floating top hitch (#24), and right rear
brace (#5).
brace (#5).
13. Secure bolt with hex flange lock nut (#12). Draw
locknut (#12) up snug and then back off 1/4 turn.
14. Install machine washer (#16) on tailwheel
spindle (#2).
15. Insert tailwheel spindle (#2) in tailwheel A-frame (#3).
16. Install spacer (#1) on tailwheel spindle (#2).
17. Insert roll pin (#23) on spindle (#2) above spacer (#1).
NOTE: You may need to lift the cutter rear or
remove bolts (#10) to assemble tail wheel (#2).
remove bolts (#10) to assemble tail wheel (#2).
NOTE: After assembly of hitch and tailwheel, push
on top of A-frame assembly (#6). It should rotate
backward and floating top link (#24) should rotate
upward. If they are too stiff to rotate, loosen nut or
nuts (#12) until top link rotates freely.
on top of A-frame assembly (#6). It should rotate
backward and floating top link (#24) should rotate
upward. If they are too stiff to rotate, loosen nut or
nuts (#12) until top link rotates freely.