Euro-Pro UV627 ユーザーズマニュアル

Fig. 7

1. Pull the dust 

container straight 
out from the side. 
(Fig. 7)

2. Empty dust 

container contents. 
(Fig. 8) If desired-
you may rinse with 
water to clean the 
dust container –
but dry thoroughly
before replacing on the sweeper.

Fig. 8

3. Replace dust container on cordless 

sweeper.

4. Periodically remove the brush cover on 

the front of the cordless sweeper and 

remove any build up of lint, hair or fiber 

on the rotating brush. To remove the 

cover - grip the cover from the bottom, 

pull out and 

upward until the 

cover unlocks 

from the side 

slots and tabs 

located on the 

top of the 

sweeper. (Fig. 9) 

Fig. 9

1a. Connect the charger plug to the charging jack or hole on the back of the sweeper. 

Plug the the charging adapter into the wall outlet. (120V., 60Hz.) Use only 

TechWorld Charger AD-1215-UL8. (Fig. 10) 

OR

1b. Connect the charger plug on the charging jack of charging stand (Fig. 11). Plug the 

charging adapter into the wall outlet (120V., 60Hz). Use only Techworld Charger 

AD-1215-UL8, and place the unit in the charging stand. (Fig. 12)

2.

This cordless sweeper is powered by Ni-Cd batteries.  Before first use, they must be 

charged for a minimum of 20 hours.

3.

When recharging the unit, the "On/Off" switch must be in the "OFF" position.

4.

The charging light indicator on the top of the sweeper will illuminate to indicate that 

the sweeper is properly charging.

5.

When the battery is running low, the speed indicator lights will start to flash. To 

recharge, repeat step #1 above. Charging times will vary depending upon the 

amount of usage between charging cycles.

Fig. 10

Fig. 11

Fig. 12

Note: Your sweeper is highly advanced and has electronic controls that optimize the 

cleaning ability and durability of the sweeper. Please review the following instructions 

carefully to ensure that all features are utilized for best performance.

1. The electronic controls of your sweeper will prevent the batteries from being deeply 

discharged and will indicate this by the speed indicator lights flashing.  The sweeper 

will then stop operating. This is normal. To start charging the unit, turn the sweeper 

off, plug in the adapter or the charging stand and attach the sweeper to charge.

2. When the sweeper on/off switch is depressed the sweeper will slowly come up to 

speed. This is done to optimize the life of all components of the sweeper and is 

normal.

3. When first started, the sweeper will start in the highest speed “III” to prevent 

overloading the unit when starting on heavy carpets. Other speeds can then be 

selected by depressing the speed selector switch.

4. For best cleaning performance, use speed “I” (low) on floors, speed “II” (medium) on 

carpets, and use speed “III” (high) for turbo deep cleaning. These are guide lines and 

you will find the optimum speed settings for your surfaces and debris to be picked up 

through use and experience.

5. The sweeper will automatically try to maintain speeds on all surfaces. The unit may 

appear to be pulsing during use to maintain it’s speed, this is normal. If this occurs, 

please select the next highest speed to gain optimum performance.

6. To protect your sweeper and it’s components, the sweeper is provided with an

electronic overload circuit. If something were to jam or overload the brush bar  

system, the units speed indicators will flash and the unit will stop operating, this is 

normal. If this occurs, first turn the unit off, then remove the obstruction before turning 

the unit on again.

Peak performance may only be realized after the unit has been charged 

and discharged two (2) or three (3) times.

To maintain peak performance of your cordless sweeper, it is 

recommended that the unit be fully discharged, then completely re-

charged at least once a month.

•

Use only with the battery pack supplied with the unit. (Item  # XBP615)

•

Do not attempt to remove the battery pack from the unit to charge it.

•

Never attempt to throw the battery pack or unit into a fire or incinerate it.

•

Do not attempt to remove or damage the battery casing.

•

Battery must be recycled or disposed of in accordance with local regulations at the 
end of it's service life. Please consult your Yellow Pages or local recycling center 
for more information.

NOTE: If, when you place the sweeper to recharge and the charging indicator 

light does NOT illuminate, then press the On/Off button once to turn 

the sweeper off. The charging indicator light should now light up.