Stiga 8211-0209-13 ユーザーズマニュアル

• Be careful when driving on slopes. No sudden 

starting or stopping when moving up or down a 

slope.

• Release the clutch pedal slowly. Always drive 

with the gear engaged, and do not disengage 

when driving down slopes.

• Never cut across a slope. Move from the top 

down, and from the bottom to the top.

• Use low acceleration when engaging the drive, 

especially in long grass. Reduce the speed on 

slopes and when making sharp turns to prevent 

the machine from tipping over or you losing 

control of the machine.

• Watch out for holes in the ground and other 

hidden dangers.

• Do not drive too near ditches or high edges.  

The machine can turn over if a wheel drives 

over the edge or the edge breaks.

• Take care when towing and when using heavy 

equipment.
a. Only use an approved towing device.
b. Limit the load so that it can be controlled 

safely.
c. Do not make any sudden turns. Take care 

when reversing.
d. Use wheel weights or front weight when 

recommended in the user instructions.

• Look out for traffic at crossings or when driving 

near roads.

• Stop the blade(s) when crossing a surface other 

than grass during mowing.

• When using any of the accessories, never direct 

the discharge at somebody standing beside it, 

and do not allow anyone to stand near the 

machine when it is running.

• Never operate the machine with insufficient 

protection or without the safety devices in 

place.

• Existing safety devices may not be 

disconnected or disengaged. Check that the 

safety devices work each time before using the 

machine.

• Do not alter the engine’s regulator setting and do 

not race the engine. The danger of personal injury 

increases when the engine is run at high revs.

• Do not touch engine components which become 

warm during use. Risk of burn injuries.

• Do not leave the driving seat without:

a. Disengaging the power take-off and lowering 

the accessories.
b. Putting the gear in neutral and activating the 

parking brake.
c. Stopping the engine and removing the key.

• Only use accessories that are approved by the 

machine’s manufacturer.

• The machine may not be used without 

accessories/tools being installed in the 

machine’s tool mounts. Driving without 

accessories can have a negative effect on the 

stability of the machine.

• Take care when using grass collectors and other 

accessories. These can alter the machine’s 

stability. Particularly on slopes.

• Disengage the drive to the accessories, shut off 

the engine and disconnect the spark plug cable 

or remove the starter key:
a. To remove sticks and rubbish or when the 

discharge has become clogged.
b. To check, clean or service the machine.
c. To check whether damage has occurred and 

to carry out any repairs before starting and 

using the machine again after a collision with a 

foreign object.
d. To check the machine if it begins to vibrate 

excessively. (Check immediately).

• Disengage the drive to accessories during 

transport or when the machine is not in use.

• Shut off the engine and disconnect the drive to 

the accessories:
a. Before filling with petrol.
b. Before removing the grass collector.
c. Before adjusting the height setting, assuming 

this cannot be done from the driver’s position.

• Reduce the acceleration when the engine is to 

be stopped, and if the engine is equipped with a 

fuel shut-off valve, this should be switched off 

when the work is finished.

• Take care with multiple blade decks as one 

rotating blade can cause other blades to rotate. 

• The machine, equipped with original 

accessories, must not be driven in any direction 

on slopes with a gradient greater than 10º.

• The cutting deck’s original blade(s) may not be 

replaced with non-original devices intended for 

e.g. moss scarification. If such devices are used, 

the guarantee will cease to be valid. There is 

also a risk of serious injury or damage to people 

or property. 

• Take care when unloading and loading the 

machine onto a trailer or lorry.

• Tighten all nuts and screws so that the machine 

is in safe working condition.

• At regular intervals check that the cutting 

deck’s blade screw(s) are properly tightened. 

• Regularly check the operation of the brakes. It