Poulan SP24H48YT ユーザーズマニュアル
30
02141
Hood
Headlight Wire
Connector
Connector
TO REMOVE HOOD AND GRILL AS-
SEM BLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Stand in front of tractor. Grasp hood at
SEM BLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Stand in front of tractor. Grasp hood at
sides, tilt toward engine and lift off of
tractor.
tractor.
4. When replacing hood, be sure to
reconnect the headlight wire con nec tor.
ENGINE
TO AD JUST THROT TLE CON TROL
CABLE
The throt tle con trol has been pre set at the
fac to ry and ad just ment should not be nec-
essary. Check adjustment as de scribed
below before loosening cable. If adjust-
ment is necessary, see engine manual.
TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your
engine does not operate properly due to
suspected carburetor problems, take your
tractor to an authorized service center/
department for repair and/or adjustment.
CABLE
The throt tle con trol has been pre set at the
fac to ry and ad just ment should not be nec-
essary. Check adjustment as de scribed
below before loosening cable. If adjust-
ment is necessary, see engine manual.
TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your
engine does not operate properly due to
suspected carburetor problems, take your
tractor to an authorized service center/
department for repair and/or adjustment.
TO REPLACE HEADLIGHT BULB
1. Raise hood.
2. Pull bulb holder out of the hole in the
1. Raise hood.
2. Pull bulb holder out of the hole in the
backside of the grill.
3. Replace bulb in holder and push bulb
holder securely back into the hole in
the backside of the grill.
the backside of the grill.
4. Close hood.
0217
9
Keps Nut
Terminal
Guard
Guard
Terminal
Access
Door
Access
Door
Hex Bolt
Positive
(Red)
Cable
(Red)
Cable
Negative
(Black)
Cable
(Black)
Cable
REPLACING BATTERY
WARNING: Do not short battery
ter mi nals by allowing a wrench or any
other object to contact both terminals at
the same time. Before connecting battery,
remove metal bracelets, wristwatch bands,
rings, etc.
Positive terminal must be connected
fi rst to prevent sparking from ac ci den tal
grounding.
1. Lift hood to raised position.
2. Remove terminal guard.
3. Disconnect BLACK battery cable
other object to contact both terminals at
the same time. Before connecting battery,
remove metal bracelets, wristwatch bands,
rings, etc.
Positive terminal must be connected
fi rst to prevent sparking from ac ci den tal
grounding.
1. Lift hood to raised position.
2. Remove terminal guard.
3. Disconnect BLACK battery cable
then RED battery cable and carefully
remove battery from tractor.
remove battery from tractor.
4. Install new battery with terminals in
same position as old battery.
5. Reinstall terminal guard.
6. First connect RED battery cable to
6. First connect RED battery cable to
positive (+) battery terminal with hex
bolt and keps nut as shown. Tighten
securely.
bolt and keps nut as shown. Tighten
securely.
7. Connect BLACK grounding cable to
negative (-) bat tery terminal with re-
main ing hex bolt and keps nut. Tight en
securely
main ing hex bolt and keps nut. Tight en
securely
8. Close terminal access doors.
9. Close hood.
9. Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause
your tractor to run poorly, stop running, or
prevent it from starting.
• Check wiring. See electrical wiring
Loose or damaged wiring may cause
your tractor to run poorly, stop running, or
prevent it from starting.
• Check wiring. See electrical wiring
diagram in the Repair Parts section.
TO REPLACE FUSE
Replace with 20 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.
Replace with 20 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.