Poulan PB19H42YT ユーザーズマニュアル

The tires on your tractor were overinflated at the factory 

for shipping purposes.  Correct tire pressure is important 

for best cutting performance.
•  Reduce tire pressure to PSI shown on tires.

For best cutting results, mower housing should be properly 

leveled.  See “TO LEVEL MOWER HOUSING” in the Service 

and Adjustments section of this manual.

See the figures that are shown for replacing motion and 

mower blade drive belts in the Service and Adjustments 

sec tion of this manual.  Verify that the belts are routed 

cor rect ly.

After you learn how to operate your tractor, check to see that 

the brake is operating properly.  See “TO CHECK BRAKE” 

in the Service and Adjustments section of this manual.

   All assembly instructions have been com plet ed.
  No remaining loose parts in carton.
  Battery is properly prepared and charged. 
  Seat is adjusted comfortably and tightened securely.
  All tires are properly inflated.  (For shipping purposes, 

the tires were overinflated at the factory).

  Be sure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results.  (Tires must be 

properly inflated for leveling).

   Check mower and drive belts.  Be sure they are routed 

properly around pulleys and inside all belt keepers.

   Check wiring.  See that all connections are still secure 

and wires are properly clamped.

   Before driving tractor, be sure free wheel control is in 

“transmission engaged” position (see “TO TRANS-

 PORT” in the Operation section of this man u al).

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY 

EXTRA ATTENTION TO THE FOLLOWING IMPORTANT 

ITEMS:

   Engine oil is at proper level.
   Fuel tank is filled with fresh, clean, regular unleaded 

gasoline.

   Become familiar with all controls, their location and 

function.  Operate them before you start the engine.

   Be sure brake system is in safe operating condition.
 

Be sure Operator Presence System and Reverse Op-

eration System (ROS) are working properly (See the 

Operation and Maintenance sections in this manual).

 

 It is important to purge the transmission before op er -

at ing your tractor for the first time.  Follow proper start-

ing and transmission purging instructions (See “TO 

START EN GINE” and “PURGE TRANSMISSION” in 

the Op er a tion section of this manual).

•  Place freewheel control in "trans mis sion dis en gaged 

position" (See “TO TRANS PORT” in the Op er a tion 

section of this manual).

•  Roll tractor forward off skid.
• 

Remove banding holding the deflector shield up against 

tractor.

  WARNING: Before start ing, read, un der stand and fol low 

all in struc tions in the Op er a tion section of this man u al. Be 

sure tractor is in a well-ventilated area. Be sure the area in  

front of tractor is clear of other peo ple and objects.
• 

Be sure all the above assembly steps have been com-

pleted.

•  Check engine oil level and fill fuel tank with gasoline.
•  Place freewheel control in "trans mis sion en gaged" 

po si tion (see "TO TRANSPORT" in Op er a tion section 

of this manual).

• 

Sit on seat in operating position, depress clutch/brake 

pedal and set the parking brake.

•  Place motion control lever in neutral (N) position.
•  Press lift lever plunger and raise attachment lift lever 

to its highest position.

•  Remove key from bag and start the engine (see "TO 

START ENGINE" in the Operation section of this man-

ual). After engine has started, move throttle control to 

idle (slow) position.

•  Release parking brake.
• 

Slowly move the mo tion control lever for ward and slowly 

drive tractor off skid.

• 

Apply brake to stop trac tor, set park ing brake and place 

motion con trol lever in neutral po si tion.

•  Turn ignition key to "STOP" position.

Continue with the in struc tions that follow.