Poulan 191663 ユーザーズマニュアル
26
Weak or Dead
Battery
Battery
Fully Charged
Battery
Battery
REPLACING BATTERY
WARNING: Do not short bat tery
ter mi nals by al low ing a wrench or any
other object to contact both terminals at
the same time. Before con nect ing battery,
remove metal bracelets, wrist watch bands,
rings, etc.
Positive terminal must be connected
fi rst to prevent spark ing from ac ci den tal
grounding.
1. Lift seat pan to raised position.
2. Disconnect BLACK battery cable fi rst
other object to contact both terminals at
the same time. Before con nect ing battery,
remove metal bracelets, wrist watch bands,
rings, etc.
Positive terminal must be connected
fi rst to prevent spark ing from ac ci den tal
grounding.
1. Lift seat pan to raised position.
2. Disconnect BLACK battery cable fi rst
then RED battery cable and carefully
remove battery from trac tor.
remove battery from trac tor.
3. Install new battery with terminals in
same position as old battery.
4. First connect RED battery cable to
positive (+) terminal with hex bolt and
keps nut as shown. Tighten securely.
Slide terminal cover over terminal
keps nut as shown. Tighten securely.
Slide terminal cover over terminal
5. Connect BLACK grounding cable to
negative (-) ter mi nal with remaining
hex bolt and keps nut. Tighten se cure ly.
hex bolt and keps nut. Tighten se cure ly.
02614
02602
02603
Seat Pan
Keps
Nut
Nut
Positive
(Red)
Cable
(Red)
Cable
Negative
(Black)
Cable
(Black)
Cable
Hex
Bolt
Bolt
Terminal
Cover
Cover
Hood
01536
Headlight Wire
Connector
Connector
TO REMOVE HOOD AND GRILL AS-
SEM BLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Stand in front of tractor. Grasp hood at
SEM BLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Stand in front of tractor. Grasp hood at
sides, tilt toward engine and lift off of
tractor.
tractor.
4. When replacing hood, be sure to
reconnect the headlight wire con nec tor.
ENGINE
TO AD JUST THROT TLE CON TROL
CABLE
The throt tle con trol has been pre set at the
fac to ry and ad just ment should not be nec-
essary. Check adjustment as de scribed
below before loosening cable. If adjust-
ment is necessary, see eingine manual.
TO ADJUST CARBURETOR
The carburetor has been preset at the
factory and adjustment should not be nec-
essary. However, minor adjustment may
be required to compensate for differences
in fuel, temperature, altitude or load. If
the carburetor des need adjustment, see
engine manual.
CABLE
The throt tle con trol has been pre set at the
fac to ry and ad just ment should not be nec-
essary. Check adjustment as de scribed
below before loosening cable. If adjust-
ment is necessary, see eingine manual.
TO ADJUST CARBURETOR
The carburetor has been preset at the
factory and adjustment should not be nec-
essary. However, minor adjustment may
be required to compensate for differences
in fuel, temperature, altitude or load. If
the carburetor des need adjustment, see
engine manual.
TO REPLACE HEADLIGHT BULB
1. Raise hood.
2. Pull bulb holder out of the hole in the
1. Raise hood.
2. Pull bulb holder out of the hole in the
backside of the grill.
3. Replace bulb in holder and push bulb
holder securely back into the hole in
the backside of the grill.
the backside of the grill.
4. Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause
your tractor to run poorly, stop running, or
prevent it from starting.
• Check wiring. See electrical wiring
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause
your tractor to run poorly, stop running, or
prevent it from starting.
• Check wiring. See electrical wiring
diagram in the Repair Parts section.
TO REPLACE FUSE
Replace with 20 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.
Replace with 20 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.
TO ATTACH JUMPER CABLES -
1. Connect one end of the RED cable
1. Connect one end of the RED cable
to the POSITIVE (+) terminal of each
battery(A-B), taking care not to short
against tractor chassis.
battery(A-B), taking care not to short
against tractor chassis.
2. Connect one end of the BLACK ca ble
to the NEGA TIVE (-) terminal (C) of
fully charged battery.
fully charged battery.
3. Connect the other end of the BLACK
cable (D) to good chassis ground,
away from fuel tank and bat tery.
away from fuel tank and bat tery.
TO REMOVE CABLES, REVERSE
ORDER -
1. BLACK cable fi rst from chassis and
ORDER -
1. BLACK cable fi rst from chassis and
then from the fully charged battery.
2. RED cable last from both batteries.