American Standard 2776.XXXW Series ユーザーズマニュアル

752561-100 Rev. D  

© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLATION.

LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR WHIRLPOOLS, ACCESS TO 
PUMP/MOTOR MAY BE MADE THROUGH ACCESS OPENING IN APRON PANEL. THE FOLLOWING PROCEDURE MUST BE USED FOR 
ALL INSTALLATIONS: LEVELING SUPPORT STRINGER SHOULD BE AS INDICATED.  THIS BATH IS NOT SELF-SUPPORTING AND MUST BE 
SUPPORTED ALONG IT'S ENTIRE BOTTOM.  SUPPORT WITH MORTAR OR GROUT.  
POSITION BATHTUB/WHIRLPOOL WITHIN THE RECESS, CHECK LEVEL, FRONT TO BACK, SIDE TO SIDE, AND SHIM AS NECESSARY.
TO SECURE THE TUB TO WOOD STUDS USE DRYWALL SCREWS W/WASHERS OR ROOFING NAILS IMMEDIATELY ABOVE THE FLANGE OF 
THE TUB.  TO SECURE THE TUB TO STEEL STUDS USE 4" DRYWALL SCREWS AND FLATWASHERS.
SEE PAGE 2 FOR COMPLETE INSTALLATION INFORMATION.

CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE TUB.
THE TILE OR SIMILAR FINISHED FLOOR WILL BE BUTTED AGAINST THE BOTTOM OF THE TUB APRON, ALSO HOLDING THE TUB IN PLACE.

19-3/4

(502mm)

7/8 WATER

RETENTION

FLANGE

(3 SIDES)

20

(508mm)

1-1/2 O.D.TAILPIECE

BATH

SUPPORT

MATERIAL

■ 

LEVELING STRINGER

NOT FOR SUPPORT 

ROUGH

FLOOR

FINISHED

WALL

TOP OF

DECK

59-7/8

(1521mm)

32

(813mm)

WATER
RETENTION
FLANGE
(3 SIDES)

7-3/4

(197mm)

12

(305mm)

2-3/8

(60mm)

(8) JETS

2-3/4

(70mm)

CUTOUT IN FLOOR
FOR DRAIN

PUMP

FINISHED

WALL

12

(305mm) OPT.

OPTIONAL TO 

FINISHED FLOOR 

USUALLY BETWEEN

65 & 78

(1651 & 1981mm)

C/L OF
OVERFLOW

4

(102 mm)

C/L OF
SPOUT

C/L OF
VALVES

C/L OF
SHOWER ARM

2-3/4

(70mm)

 4-5/8

(117mm)

1-1/2 N.P.T.M.

THREADS

3/4

(19mm)

9

(229 mm)

C/L OF

SUPPLIES

C/L OF DRAIN

SEE FITTING

SPECS FOR

DIMENSIONS

(2) AIR VALVES

ON/OFF
SWITCH

ACCESS TO PUMP/MOTOR
THROUGH REMOVABLE
FRONT ACCESS PANEL

UNDERSIDE
OF DECK

14-3/4

(375mm)

SYSTEM I PUMP

1.1 HP, 9.9 AMPS,120V.

59-7/8 x 32 x 20 (1521 x 813 x 508mm)

115 Lbs. (52 Kg.)

574 Lbs. (258 Kg.)

55 Gal. (208 L.)

  45 Gal. (171 L.)

20 x 40 (508 x 1016mm)

26 x 53-1/2 (660 x 1359mm)

14-1/2 (368mm)

 43 Lbs./Sq.Ft. (208 Kgs./Sq.m)

20.8
35.3

INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT

3

)

Carefully uncrate and inspect your new bath for any shipping 
damage. If such damage is found, report it to your vendor 
immediately.
After inspection and during installation, protect the bath from 
construction damage. Before installation, and before 
enclosing with wallboard, tile, etc., water test the unit 
and check for leaks.
If a whirlpool, do not make modifications to the whirlpool 
system or remove pump from factory mounting. This could 
adversely affect the safety and performance of the whirlpool 
and void the warranty. Do not handle or move the whirlpool by 
the pump, motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the 
bath and must be ordered separately. Framing and enclosing 
materials are provided by others. 

for selecting an American Standard bath. Your new bath is 
shipped to you after careful inspection. The whirlpool version 
is completely assembled with pump, motor, and system 
piping. All you need to finish the installation are your selected 
fittings and electrical connections for a whirlpool.
To insure maximum performance and pleasure from this 
product, please follow the instructions and cautions.

List of Required Components (not included):
•  Drain 1583.470*         •  Bath Filler*
* see your American Standard Distributor 

Tools
•  Level
•  Tape Measure
•  Pipe Wrench
•  Slip Joint Pliers
•  Screw Driver
•  Standard
      Woodworking Tools
•  Personal Safety
      Equipment
•  Caulking Gun

Supplies
•  Nails
•  Putty
•  Caulking (waterproof)
•  1 x 3 or 2 x 2
      Stringers
•  Drop Cloth
•  15 amp GFI
      Outlet
•  Cement, Plaster,
      Grout