Bühler FK311 ユーザーズマニュアル
500 & 600 Snowblower
- 6 -
500 & 600 SNOWBLOWER ASSEMBLY INSTRUCTIONS – cont’d.
4.
Hydraulic Control Assembly: (Option)
a)
Bolt the hydraulic swivel assembly (#21) to the back of the fan
housing on the left side using ½” x 1 ¼” hex bolts, lock washers
and hex nuts.
housing on the left side using ½” x 1 ¼” hex bolts, lock washers
and hex nuts.
b)
Bolt the cylinder mounting bracket (#23) to the back of the fan
housing on the right side using the same size hex bolts.
housing on the right side using the same size hex bolts.
c)
Turn the spout forward and the center of the swivel arm in line with
the spout center. With the spout and swivel arm in this position,
wrap the cable (#22) around the spout and clamp to both ends of
the swivel arm and to the bracket welded to the bottom of the
spout using 3/16" cable clamps (#20).
the spout center. With the spout and swivel arm in this position,
wrap the cable (#22) around the spout and clamp to both ends of
the swivel arm and to the bracket welded to the bottom of the
spout using 3/16" cable clamps (#20).
d)
Use a standard 8" stroke cylinder (20 ¼” min., 28 ¼” max. pin
centers).
centers).
5.
Mounting Blower on Tractor:
a)
Mount the blower on a tractor with a category 1 hitch.
b)
Using tape or a bright colored marking pen, mark on the outer
shield the position where the shaft is completely pushed together
and the position where you have a 4" overlap. Watch these marks
when moving the blower through all possible operating angles to
see that the PTO shaft stays within this range.
shield the position where the shaft is completely pushed together
and the position where you have a 4" overlap. Watch these marks
when moving the blower through all possible operating angles to
see that the PTO shaft stays within this range.
c)
With the engine on the tractor shut off, attach the PTO shaft. The
tractor end has a standard 6-spline end with a spring loaded locking
collar. The snowblower end has a clamp-style yoke with a ¼” key
way. Slide the yoke onto the gearbox shaft with the ¼” key
supplied. Lock the yoke in place with the ½” x 3" hex
bolt and lock nut fitted through the groove in the gearbox shaft.
After tightening the bolt, insert and tighten the 3/8" socket set screw
supplied. Caution: Always check to see that both ends of the
PTO shaft are securely attached every time the snowblower is
used. This should always be done with the tractor engine off.
tractor end has a standard 6-spline end with a spring loaded locking
collar. The snowblower end has a clamp-style yoke with a ¼” key
way. Slide the yoke onto the gearbox shaft with the ¼” key
supplied. Lock the yoke in place with the ½” x 3" hex
bolt and lock nut fitted through the groove in the gearbox shaft.
After tightening the bolt, insert and tighten the 3/8" socket set screw
supplied. Caution: Always check to see that both ends of the
PTO shaft are securely attached every time the snowblower is
used. This should always be done with the tractor engine off.
d)
Check that the PTO shaft does not bottom or separate with the
blower in the extreme high and low positions. Check to see which
of the four different hitch positions will allow you to keep about a 4"
minimum overlap on the PTO shields without bottoming out. This
position varies between different tractor models because of the
different lengths of the three-point arms. If the PTO shaft is still too
long with the hitch fully extended, the PTO shaft will have to be cut
shorter. Check for free movement of all parts in various raised
positions, particularly the PTO shaft.
blower in the extreme high and low positions. Check to see which
of the four different hitch positions will allow you to keep about a 4"
minimum overlap on the PTO shields without bottoming out. This
position varies between different tractor models because of the
different lengths of the three-point arms. If the PTO shaft is still too
long with the hitch fully extended, the PTO shaft will have to be cut
shorter. Check for free movement of all parts in various raised
positions, particularly the PTO shaft.