John Deere MTF-031071L ユーザーズマニュアル

ページ / 56
ST0726
Snow Thrower
MTF-031071L
OPERATOR’S
MANUAL

ユーザーズマニュアル John Deere MTF-031071L の仕様概要

  • ページ 1 ST0726 Snow Thrower OPERATOR’S MANUAL MTF-031071L
  • ページ 2 INTRODUCTION Congratulations on your purchase of a Frontier Snowthrower. It has been designed, engineered and manufactured to give you...
  • ページ 3 RULES FOR SAFE OPERATION IMPORTANT WARNING: Always disconnect the spark plug wire and place it where it cannot make...
  • ページ 4 RULES FOR SAFE OPERATION 7. Stop the engine (motor) whenever you leave the operat- Maintenance And Storage ing position,...
  • ページ 5 TABLE OF CONTENTS SAFETY DECALS . . . . . . . . . . . . . ....
  • ページ 6 SAFETY DECALS the meaning, then thoroughly read all safety and operation WARNING: If safety decals are dam- instructions in...
  • ページ 7 OWNER’S INFORMATION THREE YEAR LIMITED WARRANTY Murray warrants to the original purchaser of this Frontier Branded Snowthrower that this...
  • ページ 8 ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY CONTENTS OF SHIPPING CARTON 1 - Knife 1- Snowthrower 2 - 1/2” wrenches (or...
  • ページ 9 ASSEMBLY Figure 2 shows the snowthrower in the shipping position. Figure 3 shows the snowthrower completely assembled. Reference to...
  • ページ 10 ASSEMBLY UPPER HANDLE AND CRANK ASSEMBLY Crank 1. Loosen, but do not remove the screws, flatwashers, lock- washers and...
  • ページ 11 ASSEMBLY SNOW CHUTE ASSEMBLY 1. Position the snow chute onto the snow chute flange. Al- ign the three holes...
  • ページ 12 OPERATION READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOWTHROWER. Compare the illustrations with your SNOWTHROWER to...
  • ページ 13 OPERATION The operation of any snowthrower can result in foreign objects being thrown into the eyes,which can result in...
  • ページ 14 OPERATION TO THROW SNOW WARNING: Never run engine indoors or in an 1. Push down the auger driver lever...
  • ページ 15 OPERATION HOW TO REMOVE SNOW FROM AUGER WARNING: Do not attempt to remove snow or debris that may become...
  • ページ 16 OPERATION BEFORE STARTING ENGINE 2. Check to make sure that spark plug is tightened securely into engine and spark...
  • ページ 17 OPERATION 2. With the engine running, push the starter button and spin 5. Push the primer button as follows:...
  • ページ 18 OPERATION 10. To stop engine, move throttle control lever to STOP posi- 2. With engine running, push the “STARTER...
  • ページ 19 SERVICE RECOMMENDATIONS SERVICE RECOMMENDATIONS FIRST BEFORE EVERY EVERY EVERY BEGINNING 2 EACH 5 10 25 EACH BEFORE PROCEDURE HOUR...
  • ページ 20 MAINTENANCE Some adjustments will need to be made periodically to Remove filler plug (Figure 21), once a year. If...
  • ページ 21 MAINTENANCE LUBRICATION - EVERY 25 HOURS Chute Rotation Gear Chute Rotation Gear Lubricate the chute rotation gear with automotive...
  • ページ 22 MAINTENANCE ENGINE Check Crankcase Oil Level before starting engine and after Oil Fill Cap/Dipstick each 5 hours of continuous...
  • ページ 23 MAINTENANCE WARNING: Always turn unit off, remove igni- To adjust skids, proceed as follows: tion key and disconnect the...
  • ページ 24 MAINTENANCE BELT ADJUSTMENT Traction Drive Belt The traction drive belt has constant spring pressure and does not require an...
  • ページ 25 MAINTENANCE HOW TO REPLACE THE BELTS 9. Adjust the auger drive belt. See “How To Adjust The Au- ger...
  • ページ 26 MAINTENANCE How To Remove the Traction Drive Belt If the snow thrower will not move forward, check the traction...
  • ページ 27 MAINTENANCE BELT GUIDE ADJUSTMENT 1. Remove spark plug wire. 2. Have someone engage auger drive. Belt Guide 1/8 Inch...
  • ページ 28 MAINTENANCE Traction Drive Cable Adjustment Bolt WARNING: Drain the gasoline outdoors, away Bottom Panel from fire or flame. 1....
  • ページ 29 MAINTENANCE HOW TO ADJUST OR REPLACE 5. Install the bottom panel (see Figure 38). THE FRICTION WHEEL 6. Tighten...
  • ページ 30 MAINTENANCE How To Replace The Friction Wheel If the friction wheel is worn or damaged, the snow thrower will...
  • ページ 31 MAINTENANCE 10. Remove the three fasteners that hold the friction wheel to the hub (see Figure 44). 11. Remove...
  • ページ 32 MAINTENANCE HOW TO REMOVE THE SNOW HOOD To access the spark plug, the snow hood must be removed as...
  • ページ 33 MAINTENANCE AUGER SHEAR BOLT REPLACEMENT The augers are secured to the auger shaft with special bolts that are designed...
  • ページ 34 STORAGE OFF SEASON STORAGE 4. Thoroughly clean the snowthrower. WARNING: Never store the engine, with fuel in 5. Lubricate...
  • ページ 35 TROUBLE SHOOTING CHART PROBLEM LOOK FOR REMEDY Difficult starting Defective spark plug. Replace defective spark plug. Engine runs erratically...
  • ページ 36 REPLACEMENT PARTS WE RECOMMEND JOHN DEERE/FRONTIER quality parts and lubricants available at your John Deere/Frontier dealer. PART NUMBERS MAY...
  • ページ 37FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A ENGINE 16 1 26 2 17 20 18 12 5 22 25-2 24 13...
  • ページ 38FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A FRAME 169 160 106 162 105 167 108 111 Ref. Engine Page Ref. Auger...
  • ページ 39FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A FRAME Key No. Part No. Description 90 MT1501055E701 COVER, BOTTOM 91 MT310169 SCREW, 1/4-20X...
  • ページ 40FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A DRIVE 229 Ref. Shift Yoke Page Ref. Frame Page Ref. Wheel 200 Page 221...
  • ページ 41FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A DRIVE Key No. Part No. Description 200 MT1501092 YZ LF AXLE, SWING PLATE YZ...
  • ページ 42FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A AUGER HOUSING 550 552 551 554 553 481 482 499 490 500 527 480...
  • ページ 43FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A AUGER HOUSING Key No. Part No. Description 480 MT762146 PULLEY, 4L 6.12X .67 481...
  • ページ 44FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A DISCHARGE CHUTE 599 583 600 600 592 597 596 582 593 598 584 594...
  • ページ 45FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A DISCHARGE CHUTE Key No. Part No. Description 582 MT340720 BOLT, CARRIAGE 5/16-18 X.75 583...
  • ページ 46FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A HANDLE 766 729 731 734 739 766 730 734 735 739 729 733 740...
  • ページ 47FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A HANDLE Key No. Part No. Description 720 MT1501205E701 HANDLE, UPPER LH 721 MT1501206E701 HANDLE,...
  • ページ 48FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A SHIFT YOKE 796 793 790 792 801 791 800 814 813 802 812 Key...
  • ページ 49FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A CHUTE ROD 856 855 854 855 Ref. Handle Assy 860 863 861 864 870...
  • ページ 50FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A CONTROL PANEL 770 771 772 771 772 773 772 Key No. Part No. Description...
  • ページ 51FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A WHEELS 679 678 673 675 671 654 678 650 655 652 Ref. Drive Page...
  • ページ 52FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A GEAR CASE 341 340 327 304 326 324 323 325 306 322 311 321...
  • ページ 53FRONTIER MODEL ST0726 FACTORY MODEL 626750x16A DECALS 7 10 1 5 9 12 2 6 3 4 11 Key No....
  • ページ 54 NOTES MTF-031071L 54
  • ページ 55 NOTES MTF-031071L 55
  • ページ 56 SPECIFICATIONS ST0726 Engine Briggs & Stratton Intek Snow OHV Horsepower 7.5 hp Starter Electric / Recoil Fuel Capacity 4...
downloadlike
ArtboardArtboardArtboard