Roland FR-7 ユーザーズマニュアル
Editing sounds | 4. FREE BASS EDIT parameters
52
r
FR-7/FR-5 V-Accordion
The parameters of the FREE BS EDIT group apply to the Bass section when it is used in Free Bass mode
(see p. 24) and are saved to the selected Set. They allow you to build your own (virtual) accordion. After
setting these parameters, you probably also need to adjust the TREBLE EDIT parameters (which are also
saved to a Set). See pages 38 and 40 for how to select and adjust the parameters.
(see p. 24) and are saved to the selected Set. They allow you to build your own (virtual) accordion. After
setting these parameters, you probably also need to adjust the TREBLE EDIT parameters (which are also
saved to a Set). See pages 38 and 40 for how to select and adjust the parameters.
Press [UP] and [DOWN] simultaneously to select the value that is indicated as “Default setting”. See also “Introduction”
on p. 43 for some general hints.
on p. 43 for some general hints.
• All changes you make here apply to the last Free Bass
register you selected. So be sure to press the register
whose settings you wish to change before selecting
and editing any of the FREE BS EDIT parameters. You
can, however, decide to save your settings to a differ-
ent register (see below) if you realize that you’ve
been editing the wrong one.
whose settings you wish to change before selecting
and editing any of the FREE BS EDIT parameters. You
can, however, decide to save your settings to a differ-
ent register (see below) if you realize that you’ve
been editing the wrong one.
Any changes you make can be saved using the WRITE
function. Though there is no need to save your changes
right after performing them, please bear in mind that
they will be lost in the following cases:
function. Though there is no need to save your changes
right after performing them, please bear in mind that
they will be lost in the following cases:
• When you select another Set
• When you switch off the FR-7/FR-5
Changes you want the FR-7/FR-5 to remember must be
saved as soon as possible. Here is how:
• When you switch off the FR-7/FR-5
Changes you want the FR-7/FR-5 to remember must be
saved as soon as possible. Here is how:
(1) Press and hold the [MENU÷WRITE] button until the
following page appears:
(2) Rotate the [DATA÷ENTER] knob (or use the [UP]/
[DOWN] buttons) to select “Free Bass”.
(3) Press the [DATA÷ENTER] knob to confirm your
selection.
(4) Use the [DATA÷ENTER] knob or the [UP]/[DOWN]
buttons to specify what you want to save:
(5) Press the [DATA÷ENTER] knob to confirm your
selection.
Depending on what you chose in step (3) above, the
display now looks as follows:
Depending on what you chose in step (3) above, the
display now looks as follows:
(6) Enter a name for the register you are about to
save.
See p. 43 for details. Changing the name is only nec-
essary if you don’t agree with the name that appears
in the display.
See p. 43 for details. Changing the name is only nec-
essary if you don’t agree with the name that appears
in the display.
(7) Press the [MENU÷WRITE] button to jump to the fol-
lowing page:
(8) Use the [DATA÷ENTER] knob or the [UP]/[DOWN]
buttons to select the Set that should contain your
changed version(s).
Change this setting only if you do not want to save
your settings to the current Set.
changed version(s).
Change this setting only if you do not want to save
your settings to the current Set.
(9) (Only for “Current”:)
Press the [DATA÷ENTER] knob to select “REGISTER”,
then turn it to select the number of the register
where you want to save your edited version (1~7).
then turn it to select the number of the register
where you want to save your edited version (1~7).
Important notes
Saving your changes
Current: The register you are currently editing.
Currnt +
SCom:
SCom:
ALL
All registers. This is probably the safest
bet, because it ensures that no Free Bass
register will be forgotten. (It is perfectly
possible to edit several registers without
saving them.)
bet, because it ensures that no Free Bass
register will be forgotten. (It is perfectly
possible to edit several registers without
saving them.)
If you selected “Current” or
“Curnt+SCom”
“Curnt+SCom”
If you selected “ALL”
→ Skip to step (8)
If you selected “Current” or “Curnt+SCom”