Roland BK-5 ユーザーズマニュアル
MIDI parameters
Backing Keyboard BK-5
r
105
Rx Event
The “Rx Event” section provides a number of filters
that allow you to specify whether the messages in
question should be received (On) or not (Off).
The “Rx Event” section provides a number of filters
that allow you to specify whether the messages in
question should be received (On) or not (Off).
The following parameters are located on the display
page that can be selected using [MENU] button‰
“MIDI” ‰ “Edit Tone Parts”.
page that can be selected using [MENU] button‰
“MIDI” ‰ “Edit Tone Parts”.
1.
Use the [CURSOR÷VALUE] dial to select the
part you want to edit (Upper1, Upper2,
Lower, Mel.Intell).
part you want to edit (Upper1, Upper2,
Lower, Mel.Intell).
2.
Press the [ENTER/SELECT] button.
The display now shows the settings for the selected
part.
part.
Tx, Tx Ch, Tx Shift, Tx Local, Tx Event
For the explanation of these parameters please refer
to page 104.
For the explanation of these parameters please refer
to page 104.
Rx, Rx Ch, Rx Shift, Rx Limit Low/High, Rx Event
For the explanation of these parameters please refer
to page 104.
For the explanation of these parameters please refer
to page 104.
The following parameters are located on the display
page that can be selected using [MENU] button‰
“MIDI” ‰ “Edit Song Parts”.
page that can be selected using [MENU] button‰
“MIDI” ‰ “Edit Song Parts”.
1.
Use the [CURSOR÷VALUE] dial to select the
part you want to edit (Part 1~16).
part you want to edit (Part 1~16).
2.
Press the [ENTER/SELECT] button.
The display now shows the settings for the selected
part.
part.
Tx, Tx Ch, Tx Shift, Tx Local, Tx Event
For the explanation of these parameters please refer
to page 104.
For the explanation of these parameters please refer
to page 104.
Rx, Rx Ch, Rx Shift, Rx Limit Low/High, Rx Event
For the explanation of these parameters please refer
to page 104.
For the explanation of these parameters please refer
to page 104.
Filter
Setting
Explanation
Program
Change
Change
Off, On
Select “On” to receive pro-
gram change and bank
select (CC00, CC32) mes-
sages.
gram change and bank
select (CC00, CC32) mes-
sages.
Pitch Bender
Off, On
Select “On” to receive Pitch
Bend messages.
Bend messages.
Modulation
Off, On
Select “On” to receive Mod-
ulation messages (CC01).
ulation messages (CC01).
Volume
Off, On
Select “On” to receive Vol-
ume messages (CC07).
ume messages (CC07).
Panpot
Off, On
Select “On” to receive Pan-
pot messages (CC10).
pot messages (CC10).
Expression
Off, On
Select “On” to receive
Expression messages
(CC11).
Expression messages
(CC11).
Reverb
Off, On
Select “On” to receive
Reverb messages (CC91).
Reverb messages (CC91).
Chorus
Off, On
Select “On” to receive Cho-
rus messages (CC93).
rus messages (CC93).
Hold
Off, On
Select “On” to receive Hold
messages (CC64).
messages (CC64).
Sostenuto
Off, On
Select “On” to receive Sos-
tenuto messages (CC66).
tenuto messages (CC66).
Soft
Off, On
Select “On” to receive Soft
messages (CC67).
messages (CC67).
Caf
Off, On
Select “On” to receive Caf-
Channel aftertouch.
Channel aftertouch.
RPN
Off, On
Select “On” to receive Reg-
istered parameter number
messages (CC100/101).
istered parameter number
messages (CC100/101).
NRPN
Off, On
Select “On” to receive Non-
registered parameter num-
ber messages (CC98/99).
registered parameter num-
ber messages (CC98/99).
System
Exclusive
Exclusive
Off, On
Select “On” to receive Sys-
tem Exclusive messages.
tem Exclusive messages.
CC16
Off, On
General purpose controller
that allows you to influence
the “C1” parameter (see
p. 60). Select “On” to receive
this message type.
that allows you to influence
the “C1” parameter (see
p. 60). Select “On” to receive
this message type.
Select All
Off, On
Select “On” to receive all
MIDI message listed above.
MIDI message listed above.
BK-5_US.book Page 105 Monday, November 14, 2011 12:43 PM