Roland RD-700GX ユーザーズマニュアル
2
MIDI Implementation
❍
Resonance (Controller number 71)
Status
2nd byte
3rd byte
BnH
47H
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv= Resonance value (relative change):
00H - 7FH (-64 - 0 - +63)
*
The Resonanse parameter (Tone Info: Resonance) will change.
❍
Release Time (Controller number 72)
Status
2nd byte
3rd byte
BnH
48H
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Release Time value (relative change): 00H - 7FH (-64 - 0 - +63)
*
The Release Time parameter (Tone Info: Release Time) will change.
❍
Attack time (Controller number 73)
Status
2nd byte
3rd byte
BnH
49H
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Attack time value (relative change): 00H - 7FH (-64 - 0 - +63),
*
The Attack Time parameter (Tone Info: Attack Time) will change.
❍
Cutoff (Controller number 74)
Status
2nd byte
3rd byte
BnH
4AH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Cutoff value (relative change):
00H - 7FH (-64 - 0 - +63)
*
The Cutoff parameter (Tone Info: Cutoff) will change.
❍
Decay Time (Controller number 75)
Status
2nd byte
3rd byte
BnH
4BH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Decay Time value (relative change): 00H - 7FH (-64 - 0 - +63)
*
The Decay parameter (Tone Info: Decay) will change.
❍
Vibrato Rate (Controller number 76)
Status
2nd byte
3rd byte
BnH
4CH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Rate value (relative change): 00H - 7FH (-64 - 0 - +63)
❍
Vibrato Depth (Controller number 77)
Status
2nd byte
3rd byte
BnH
4DH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Depth Value (relative change):00H - 7FH (-64 - 0 - +63)
❍
Vibrato Delay (Controller number 78)
Status
2nd byte
3rd byte
BnH
4EH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Delay value (relative change):00H - 7FH (-64 - 0 - +63)
❍
Portamento Control (Controller number 84)
Status
2nd byte
3rd byte
BnH
54H
kkH
n = MIDI channel number:
0H - FH (ch.1 - 16)
kk = source note number:
00H - 7FH (0 - 127)
*
A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
continuously in pitch, starting from the pitch of the Source Note Number.
*
If a voice is already sounding for a note number identical to the Source Note Number,
this voice will continue sounding (i.e., legato) and will, when the next Note-on is
received, smoothly change to the pitch of that Note-on.
this voice will continue sounding (i.e., legato) and will, when the next Note-on is
received, smoothly change to the pitch of that Note-on.
*
The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value.
Portamento Time value.
❍
Effect 1 (Reverb Send Level) (Controller number 91)
Status
2nd byte
3rd byte
BnH
5BH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Reverb Send Level:
00H - 7FH (0 - 127)
*
The Reverb Amount parameter (Tone Info: Reverb Amount) will change.
❍
Effect 3 (Chorus Send Level) (Controller number 93)
Status
2nd byte
3rd byte
BnH
5DH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Chorus Send Level:
00H - 7FH (0 - 127)
*
The Chorus Amount parameter (Tone Info: Chorus Amount) will change.
❍
RPN MSB/LSB (Controller number 100, 101)
Status
2nd byte
3rd byte
BnH
65H
mmH
BnH
64H
llH
n = MIDI channel number:
0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then Data Entry (Controller numbers
6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry
messages that is received at the same MIDI channel after that are recognized as changing
toward the value of the RPN messages. In order not to make any mistakes, transmitting
RPN Null is recommended after setting parameters you need.
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then Data Entry (Controller numbers
6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry
messages that is received at the same MIDI channel after that are recognized as changing
toward the value of the RPN messages. In order not to make any mistakes, transmitting
RPN Null is recommended after setting parameters you need.
This device receives the following RPNs.
RPN
Data entry
MSB, LSB
MSB, LSB
Notes
00H, 00H
mmH, llH
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
*
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
*
The Bend Range parameter (Tone Info: Bend Range) will
change.
change.
00H, 01H
mmH, llH
Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
*
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
*
The Fine Tune parameter (Tone Info: Fine Tune) will
change.
change.
00H, 02H
mmH, llH
Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
*
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
*
The Coarse Tune parameter (Tone Info: Coarse Tune)
will change.
will change.
00H, 05H
mmH, llH
Modulation Depth Range
mm, ll: 00 00H - 06 00H ( 0 - 16384 x 600 / 16384 cent)
mm, ll: 00 00H - 06 00H ( 0 - 16384 x 600 / 16384 cent)
7FH, 7FH
---, ---
RPN null
RPN and NRPN will be set as “unspecified.” Once this
setting has been made, subsequent Parameter values that
were previously set will not change.
mm, ll: ignored
RPN and NRPN will be set as “unspecified.” Once this
setting has been made, subsequent Parameter values that
were previously set will not change.
mm, ll: ignored
●
Program Change
Status
2nd byte
CnH
ppH
n = MIDI channel number:
0H - FH (ch.1 - 16)
pp = Program number:
00H - 7FH (prog.1 - prog.128)
*
Not received when the Rx Program Change parameter (EDIT: Part Parameter: Rx
Program Chanage) is OFF.
Program Chanage) is OFF.