Roland SP-555 ユーザーズマニュアル
19
Using effects
The SP-555 lets you choose either of the following two
methods of operation to specify what will happen to the knob
settings when you switch from one type of effect to another.
methods of operation to specify what will happen to the knob
settings when you switch from one type of effect to another.
1.
While holding down [CANCEL], press [SUPER FILTER].
Each time you press [SUPER FILTER], the display’s
indication will alternate between “C.nL” and “C.JP.”
Each time you press [SUPER FILTER], the display’s
indication will alternate between “C.nL” and “C.JP.”
“C.JP” (Jump):
The setting of the parameter will match the knob
position the instant you turn the knob.
position the instant you turn the knob.
“C.nL” (Null):
When you start turning the knob, the setting will not
actually change until the knob position passes
through the current value of the setting.
When you turn on the power, this is always set to
“C.JP” (Jump).
actually change until the knob position passes
through the current value of the setting.
When you turn on the power, this is always set to
“C.JP” (Jump).
Applying the same effect to more than
one pad (EFFECT ASSIGN)
one pad (EFFECT ASSIGN)
To apply the same effect to one or more pads in addition to
the current pad, hold down [EFFECT ASSIGN] and press the
desired pad.
the current pad, hold down [EFFECT ASSIGN] and press the
desired pad.
The same effect is applied to each pad that lights when you
press [EFFECT ASSIGN].
press [EFFECT ASSIGN].
If you hold down [EFFECT ASSIGN] while together pressing
both [PAD 1] and [PAD 16], you can simultaneously turn the
effect on/off for all pads in that bank.
both [PAD 1] and [PAD 16], you can simultaneously turn the
effect on/off for all pads in that bank.
By default, if you select as the current pad a pad to which
the effect is not applied, and then turn the effect on/off or
change the effect settings, the effect assign settings will be
cancelled, so that the effect is applied only to the current
pad.
the effect is not applied, and then turn the effect on/off or
change the effect settings, the effect assign settings will be
cancelled, so that the effect is applied only to the current
pad.
Effect assign mode
If you hold down [EFFECT ASSIGN] and press [REMAIN],
the [EFFECT ASSIGN] button will light. In this state, the
EFFECT ASSIGN setting for each pad will not be cancelled
even if you change the current pad.
the [EFFECT ASSIGN] button will light. In this state, the
EFFECT ASSIGN setting for each pad will not be cancelled
even if you change the current pad.
If you once again hold down [EFFECT ASSIGN] and press
[REMAIN], the [EFFECT ASSIGN] button will go out, and the
EFFECT ASSIGN setting will change when you change the
current pad.
[REMAIN], the [EFFECT ASSIGN] button will go out, and the
EFFECT ASSIGN setting will change when you change the
current pad.
You can also change the power-on default state. (
➜
“Parameters whose power-on
default setting can be changed.”
)
Effect knob control
In the “C.nL” (Null) state, the display will indicate the
relation between the knob position and the value of the
setting. This will help you match the knob position with
the value.
relation between the knob position and the value of the
setting. This will help you match the knob position with
the value.
When the value is lower than the knob position
When the knob position is lower than the value
Tips for using effects
Effect
Pad lit
on
Pad unlit
off
Current pad: blinking, lit longer
on
Current pad: blinking, lit briefly
off
SP-555_e.book 19 ページ ２００７年６月２５日 月曜日 午前９時９分