Korg Triton Studio ユーザーズマニュアル

Here you can create drum kits by assigning a drum instru-
ment (drum sample) to each key.
A drum kit that you create or edit here can be selected in 
Program mode P1: Edit Basic “Drum Kit” (when “Oscilla-
tor Mode

” is Drums) as an oscillator, and processed through 

the filter, amp and effects in the same way as a “multisam-
ple” (when “Oscillator Mode” is Single or Double).

When you wish to edit a drum kit, enter Program mode, 
select a program that uses a drum kit (i.e., whose “Oscillator 
Mode” is Drums), and then move to this page. A program 
that uses a drum kit will already have filter, amp, and effect 
settings etc. suitable for drum sounds. (Programs in the sep-
arate “VNL” that use a drum kit are indicated by a 

 sym-

bol.)
Even if a program with an “Oscillator Mode” of Single or 
Double

 is selected in Program mode, the program will 

sound using its own filter and amp settings etc. Effects will 
sound according to the settings of the program you selected. 
You must set “Octave” (Program P1: 1–2a) to +0[8']. With 
any setting other than +0[8'], the key locations and drum 
sounds will not correspond correctly.

When a particular drum kit is edited, all programs that 
use that drum kit will be affected.

If “Enable Exclusive” (1–1b) is checked, the drum kit 
can be edited using exclusive data.

If you want the edited drum kit settings to be backed 
up after you turn off the power, you must write them 
into memory.
Execute the page menu command “Write Global Set-
ting” or press the SEQUENCER [REC/WRITE] key to 
access the dialog box, and write the settings.

☞For details on creating a drum kit, refer to BG p.128.

Here you can select a drum kit, assign High and Low drum 
samples to each key, and set parameters for the High and 
Low drum samples.

Selects the drum kit that you wish to edit.

If you want to edit a drum kit (such as a preloaded 
drum kit) that is used by a program, it is a good idea to 
use the page menu command “Copy Drum Kit” to copy 
it to an unused number in 016 (E-A)–143 (User), and 
then edit the copy. Numbers 016 (E-A)–127 (E-G) are 
normally used to load drum kits for the EXB-PCM 
series options (some models do not have included 
drum kits).

If you want to edit the name of the drum kit, execute 
the page menu command “Rename Drum Kit.”

Selects the key to which the drum sample (and its settings) 
will be assigned.
Use the VALUE controller to specify the key. You can also 
select the key by holding down the [ENTER] key and play-
ing a note on the keyboard.
Two drum samples, High and Low, can be assigned to each 
key, allowing you to switch between them by velocity.
If you check “Assign” for the key you select here, the High 
Drumsample

, Low Drumsample, Voice Assign Mode, and 

parameters (see below) will be used.

 The drum samples you assigned for “High 

” and “Low Drumsample” will sound. Nor-

mally you will check this parameter.
Off (unchecked):

 The selected drumsamples will be invalid, 

and the drum samples of the key to the right will sound. At 
this time, the pitch will be a semitone lower than the pitch of 
the key to the right. Uncheck this parameter when you wish 
to play a drumsample at differing pitches.

→Hi

Specifies the velocity value at which you will switch from 
the “Low Drumsample” to the “High Drumsample.” Veloc-
ities above this value will sound the “High Drumsample,” 
and velocities below this value will sound the “Low Drum-
sample

.” If you do not wish to use velocity switching, set 

this to 001 and specify only the “High Drumsample” 
(

☞“Velocity M.Sample SW Lo

→

Hi” Program P1: 1–2c).

Selects the High drum sample by its bank and drumsample 
number. The drumsample you select here will sound when 
the velocity is greater than the “Velocity Sample SW 
Lo

→

” (5–1a) setting.

Selects preset drum samples. For “High Drumsam-

” you can select from 000: BD-Dry 1–416: Vox-Wah Gtr 4. 

5–1

5–1a

5–1b

5–1c

Preloaded drum kits

User drum kits,
EXB-PCM series drum kits

User drum kits
(some preloaded drum kits)