Korg Triton Studio ユーザーズマニュアル

The Wah parameter switches the wah effect on/off.

This parameter sets how the wah effect is switched on and off via 
the modulation source.
When “Sw” = Moment, the wah effect is usually turned off. It is 
turned on only when you press the pedal or operate the joystick.

When a value for the modulation source is less than 64, 
“off” speed is selected, and when the value is 64 or higher, 
“on” is selected.

When “Sw” = Toggle, the wah effect is switched between on and 
off each time you press the pedal or operate the joystick.

The switch will be turned on/off each time the value of the 
modulation source exceeds 64.

This parameter sets the sweep range of the wah center frequency. 
A negative value will reverse the direction of sweep. The wah cen-
ter frequency can be controlled by the modulation source speci-
fied in the “Wah Sweep Src” parameter.

The degree of distortion is determined by the level of input signal 
and the setting of “Drive”. Raising the “Drive” setting will cause 
the entire volume level to increase. Use the “Output Level” 
parameter to adjust the volume level. The “Output Level” param-
eter uses the signal level input to the 3-Band EQ. If clipping occurs 
at the 3-Band EQ, adjust the “Output Level” parameter.

Cutting the signal in the low range before it is input to the Distor-
tion will create a sharp distortion.

These parameters set the bandwidth of each equalizer. The higher 
the value, the narrower the band becomes.

This is a stereo 4-band parametric equalizer. You can select 
peaking type or shelving type for Band 1 and 4. The gain of 
Band 2 can be controlled by dynamic modulation.

Selects a filter type for Band 1 and 4.

e

Output Level
Sets the output level

0...50

☞

, 

Src

Off...Tempo

Selects the modulation source for the output level

Amt
Sets the modulation amount of the output level

–50...+50

f

Low Cutoff [Hz]

20...1.0kHz

Sets the center frequency for Low EQ (shelving type)

Gain [dB]
Sets the gain of Low EQ

–18...+18dB

g

Mid1 Cutoff [Hz]

300...10.00kHz

Sets the center frequency for Mid/High EQ 1 (peaking type)

Q
Sets the band width of Mid/High EQ 1

0.5...10.0

☞

Gain [dB]
Sets the gain of Mid/High EQ 1

–18...+18dB

h

Mid2 Cutoff [Hz]

500...20.00kHz

Sets the center frequency for Mid/High EQ 2 (peaking type)

Q
Sets the band width of Mid/High EQ 2

0.5...10.0

☞

Gain [dB]
Sets the gain of Mid/High EQ 2

–18...+18dB

i

Direct Mix

0...50

Sets the amount of the dry sound mixed to the distortion

Speaker Simulation
Switches the speaker simulation on/off

Off, On

j

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Sets the modulation amount of the effect balance

–100...+100

a

Trim
Sets the input level

0...100

b

Band1 Type

Peaking, Shelving-Low

Selects the type of Band 1

☞

c

Band4 Type

Peaking, Shelving-High

Selects the type of Band 4

☞

d

Band2 Dynamic Gain Src
Selects the modulation source of the Band 2 gain

Off...Tempo

☞

Amt [dB]
Sets the modulation amount of Band 2 gain

–18...+18dB

☞

e

Band1 Cutoff [Hz]
Sets the center frequency of Band 1

20...1.00kHz

Q
Sets the bandwidth of Band 1

0.5...10.0

☞

 Fx:006

Gain [dB]
Sets the gain of Band 1

–18.0...+18.0dB

f

Band2 Cutoff [Hz]
Sets the center frequency of Band 2

50...10.00kHz

Q
Sets the bandwidth of Band 2

0.5...10.0

☞

 Fx:006

Gain [dB]
Sets the gain of Band 2

–18.0...+18.0dB

☞

,

g

Band3 Cutoff [Hz]
Sets the center frequency of Band 3

300...10.00kHz

Q
Sets the bandwidth of Band 3

0.5...10.0

☞

 Fx:006

Gain [dB]
Sets the gain of Band 3

–18.0...+18.0dB

h

Band4 Cutoff [Hz]
Sets the center frequency of Band 4

500...20.00kHz

Q
Sets the bandwidth of Band 4

0.5...10.0

☞

 Fx:006

Gain [dB]
Sets the gain of Band 4

–18.0...+18.0dB

i

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Sets the modulation amount of the effect balance

–100...+100