Korg Triton Studio ユーザーズマニュアル

This effect combines a mono-type phaser and a chorus/
flanger.

This effect combines a mono-type reverb and a gate.

The “Envelope Select” parameter enables you to select whether 
turning the gate on and off is triggered by the input signal level or 
controlled directly by the modulation source. You can select from 
Off

 to Gate2+Dmpr for the Src parameter to specify the modula-

tion source. 
When “Envelope Select” is set to Input, the gate is controlled by 
the level of signals that are the combination of the dry sound and 
the reverb sound. When the signal level exceeds the threshold, the 
gate opens and the reverb sound is output.
Normally, set “Input Reverb Mix” to Dry (the gate is controlled 
only by the dry sound). If you wish to extend the gate time, set the 
“Input Reverb Mix” value higher and adjust the “Threshold” 
value.

a

[P] LFO Frequency [Hz]
Sets the LFO speed

0.02...20.00Hz

LFO Waveform
Selects LFO Waveform

Triangle, Sine

b

[P] Manual
Sets the frequency to which the effect is applied

0...100

Depth
Sets the depth of LFO modulation

0...100

Resonance
Sets the resonance amount

–100...+100

☞

 Fx:023

c

[P] Phaser Wet/Dry

–Wet...–2:98, Dry, 2:98...Wet

Sets the phaser effect balance

☞

 Fx:010, 023

d

[F] LFO Frequency [Hz]
Sets the LFO speed

0.02...20.00Hz

LFO Waveform
Selects LFO Waveform

Triangle, Sine

e

[F] Delay Time [msec]
Sets the delay time

0.0...50.0msec

Depth
Sets the depth of LFO modulation

0...100

Feedback
Sets the feedback amount

–100...+100

☞

 Fx:020

f

[F] EQ Trim
Sets the EQ input level

0...100

g

[F] Pre LEQ Gain [dB]
Sets the gain of Low EQ

–15...+15dB

Pre HEQ Gain [dB]
Sets the gain of High EQ

–15...+15dB

h

[F] Cho/Flng Wet/Dry

–Wet...–2:98, Dry, 2:98...Wet

Sets the effect balance of the chorus/flanger

☞

 Fx:010, 020

Output Mode

Normal, Wet Invert

Selects the output mode for the chorus/flanger

☞

 Fx:060

i

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Sets the modulation amount of the effect balance

–100...+100

+

a

[R] Reverb Time [sec]
Sets the reverberation time

0.1...10.0sec

High Damp [%]
Sets the damping amount in the high range

0...100%

b

[R] Pre Delay [msec]

0...200msec

Sets the delay time of the reverb sound and gate control signal

c

[R] EQ Trim
Sets the EQ input level

0...100

d

[R] Pre LEQ Gain [dB]
Sets the gain of Low EQ

–15...+15dB

Pre HEQ Gain [dB]
Sets the gain of High EQ

–15...+15dB

e

[R] Reverb Balance

Dry, 1:99...99:1, Wet

Sets the reverb effect balance

f

[G] Envelope Select

D-mod, Input

Switches between modulation source control and input signal control 

☞

Src

Off...Gate2+Dmpr

Selects the modulation source that controls the gate when Envelope 
Select is set to D-mod

☞

g

[G] Input Reverb Mix

Dry, 1:99...99:1, Wet

Sets the balance between the dry and reverb sounds of the gate con-
trol signal.

☞

Threshold
Sets the gate threshold level

0...100

☞

h

[G] Polarity

+, –

Switches between non-invert and invert of the gate on/off state

☞

 Fx:005

i

[G] Attack
Sets the attack time

1...100

☞

 Fx:005

Release
Sets the release time

1...100

☞

 Fx:005

j

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Sets the modulation amount of the effect balance

–100...+100

+