Korg Triton Studio ユーザーズマニュアル

This effect has six chorus blocks with different LFO phases. 
You can produce a complex stereo image by setting a different 
delay time and depth for each block. You can control the 
delay output level via a modulation source.

These parameters set the output status of each Tap.
Always On

: Output is always on. (No modulation)

: Output is always off. (No modulation)

→

: Output level is switched from on to off depending 

on the modulation source.
Off

→

: Output level is switched from off to on depending 

on the modulation source.
Combining these parameters, you can change from 4-phase cho-
rus to two-tap delay by crossfading them gradually via the modu-
lation source during a performance.

This parameter selects combinations of stereo images of the tap 
outputs.

Tap output level, feedback amount and effect balance are con-
trolled simultaneously via a modulation source.

This is a stereo pitch shifter. The pitch shift amount for the left 
and right channels can be reversed from each other.

a

LFO Frequency [Hz]
Sets the LFO speed

0.02...13.00Hz

b

Tap1(000) [msec]
Sets the Tap1 (LFO phase=0 degrees) delay time

0...570msec

Depth
Sets the Tap1 chorus depth

0...30

Status

Always On, Always Off, On

→

Off(dm), Off

→

On(dm)

Selects on, off, or modulation source for the control of Tap1 output

☞

,

c

Tap2(180) [msec]

0...570msec

Sets the Tap2 (LFO phase=180 degrees) delay time

Depth
Sets the Tap2 chorus depth

0...30

Status

Always On, Always Off, On

→

Off(dm), Off

→

On(dm)

Selects on, off, or modulation source for the control of Tap2 output

☞

,

 

d

Tap3(060) [msec]

0...570msec

Sets the Tap3 (LFO phase=60 degrees) delay time

Depth
Sets the Tap3 chorus depth

0...30

Status

Always On, Always Off, On

→

Off(dm), Off

→

On(dm)

Selects on, off, or modulation source for the control of Tap3 output

☞

,

e

Tap4(240) [msec]

0...570msec

Sets the Tap4 (LFO phase=240 degrees) delay time

Depth
Sets the Tap4 chorus depth

0...30

Status

Always On, Always Off, On

→

Off(dm), Off

→

On(dm)

Selects on, off, or modulation source for the control of Tap4 output

☞

,

f

Tap5(120) [msec]

0...570msec

Sets the Tap5 (LFO phase=120 degrees) delay time

Depth
Sets the Tap5 chorus depth

0...30

Status

Always On, Always Off, On

→

Off(dm), Off

→

On(dm)

Selects on, off, or modulation source for the control of Tap5 output

☞

,

g

Tap6(300) [msec]

0...570msec

Sets the Tap6 (LFO phase=300 degrees) delay time

Depth
Sets the Tap6 chorus depth

0...30

Status

Always On, Always Off, On

→

Off(dm), Off

→

On(dm)

Selects on, off, or modulation source for the control of Tap6 output

☞

,

h

Panning Preset
Specifies the stereo image of each Tap

1, 2, 3, 4

☞

+

i

Tap1 Feedback
Sets the Tap1 feedback amount

–100...+100

Src

Off...Tempo

Selects the modulation source for the Tap output level, feedback 
amount, and effect balance 

☞

Amt

–100...+100

Sets the modulation amount of Tap1 feedback amount

☞

j

Wet/Dry

Dry, 1:99...99:1, Wet

Amt
Sets the modulation amount of the effect balance

–100...+100

☞

a

Mode

Slow, Medium, Fast

Switches Pitch Shifter mode

☞

 Fx:038

b

L/R Pitch

Normal, Up/Down

Determines whether or not the L/R pitch shift amount is inverted

☞

c

Pitch Shift [1/2tone]

–24...+24

Sets the pitch shift amount in steps of a semitone

☞

 Fx:038,

Src

Off...Tempo

Selects the modulation source of pitch shift amount

☞

 Fx:038

Amt
Sets the modulation amount of pitch shift amount

–24...+24

☞

 Fx:038

d

Fine [cent]

–100...+100cent

Sets the pitch shift amount in steps of one cent

☞

 Fx:038,

Amt
Sets the modulation amount of pitch shift amount

–100...+100cent

☞

 Fx:038

e

Lch Delay [msec]
Sets the delay time for the left channel

0...1000msec

Rch Delay [msec]
Sets the delay time for the right channel

0...1000msec

f

Feedback Position
Switches the feedback connection

Pre, Post

☞

 Fx:038

g

Feedback
Sets the feedback amount

–100...+100

☞

 Fx:038

High Damp [%]
Sets the damping amount in the high range

0...100%