Korg Triton Studio ユーザーズマニュアル
45
Combination
P0
P1
P2
P3
P4
P7
P8
P9
▼ 7–1: Page Menu Command
7–1A: Copy Arpeggiator
This command can copy arpeggiator settings from another
location to the current Combi.
location to the current Combi.
1
Select “Copy Arpeggiator” to access the dialog box.
2
In “From” select the source (mode, bank, number) of the
arpeggiator you wish to copy.
If you are copying from Combination, Song, or Song Play
mode, select either A or B to if you wish to copy settings
from only one arpeggiator, or select A&B if you wish to
copy the settings of both arpeggiators.
arpeggiator you wish to copy.
If you are copying from Combination, Song, or Song Play
mode, select either A or B to if you wish to copy settings
from only one arpeggiator, or select A&B if you wish to
copy the settings of both arpeggiators.
3
If you are copying from a Program, or are copying either
A or B from Combination, Song, or Song Play mode,
select either A or B as the “To” copy destination.
A or B from Combination, Song, or Song Play mode,
select either A or B as the “To” copy destination.
4
To execute the Copy Arpeggiator command, press the
OK button
OK button
. To cancel, press the Cancel button.
7–2: Arpegg. A
(Arpeggiator A)
7–3: Arpegg. B
(Arpeggiator B)
The Arpeggiator A pages allow you to adjust the settings for
arpeggiator A. The Arpeggiator B pages allow you to adjust
the settings for arpeggiator B.
arpeggiator A. The Arpeggiator B pages allow you to adjust
the settings for arpeggiator B.
You can also use the “Copy Arpeggiator” page menu
command to copy arpeggiator settings from Program
mode or another mode.
command to copy arpeggiator settings from Program
mode or another mode.
7–2(3)a: Arpeggiator-A(B) Setup
Pattern*
[P00...P04, U000(I-A/B)...U506(User)]
Octave*
[1, 2, 3, 4]
Resolution*
[
, , , , , ]
Gate
[000...100%, Step]
Velocity
[001...127, Key, Step]
Swing
[–100...+100%]
Sort*
[Off, On]
Latch*
[Off, On]
Key Sync.*
[Off, On]
Keyboard*
[Off, On]
These parameters are the arpeggiator settings for the combi-
nation. (
nation. (
☞“Program P7: Edit-Arpeggiator”)
* These parameters can also be set from “0–3(4): Arpegg.
A(B)”.
7–4: Scan Zone
(Scan Zone A/B)
These settings specify the note and velocity ranges that will
operate arpeggiators A and B.
operate arpeggiators A and B.
7–4a: Zone Map
This shows the Scan Zone for each arpeggiator, A and B.
7–4b: Scan Zone A/B
A:
Top Key
[C–1...G9]
Bottom Key
[C–1...G9]
Specifies the range of notes (keys) that will operate arpeg-
giator A. “Top Key” specifies the upper limit, and “Bottom
Key” specifies the lower limit.
giator A. “Top Key” specifies the upper limit, and “Bottom
Key” specifies the lower limit.
Top Velocity
[001...127]
Bottom Velocity
[001...127]
Specifies the range of velocities that will operate arpeggiator
A. “Top Velocity” specifies the upper limit, and “Bottom
Velocity” specifies the lower limit.
A. “Top Velocity” specifies the upper limit, and “Bottom
Velocity” specifies the lower limit.
B:
Top Key
[C–1...G9]
Bottom Key
[C–1...G9]
Top Velocity
[001...127]
Bottom Velocity
[001...127]
Specifies the range of notes (keys) and velocities that will
operate arpeggiator B (
operate arpeggiator B (
☞A:).
The values of these parameters can also be entered by
holding down the [ENTER] key and playing a note on
the keyboard.
holding down the [ENTER] key and playing a note on
the keyboard.
0–1A
0–1B
7–1A
7–1
7–1a
7–2a
1–1a
7–1
7–4a
7–4b
7–1a
1–1a
C–1
G9
Key zone of arpeggiator A
Velocity zone of
arpeggiator A
arpeggiator A
Velocity zone of
arpeggiator B
arpeggiator B
Key zone of arpeggiator B