Korg Electric Keyboard ユーザーズマニュアル

■

☞ “Delete SMPL,” “Copy SMPL,” “Move SMPL,” “Rename 

SMPL,” “SMPL To Stereo,” “Delete MS,” “Copy MS,” 
“Move MS,” “Rename MS,” “MS To Stereo/MS To 
Mono,” “Conv. To Prog,” “Keyboard Disp.” (1.1–3f)

Specify the input level from the rear panel AUDIO INPUT 1, 
2, and set pan and bus. You can also set other setup parame-
ters.

Here you can make adjustments for the input stage of the 
audio signal received at AUDIO INPUT 1 and 2.

These settings are valid only in Sampling mode. These 
settings will also be valid when you move from Sam-
pling mode to Global mode.

In modes other than Sampling mode, settings for Audio 
Input 1 and 2 are made in “Audio In (Setup for COMBI, 
PROG, SEQ)” (GLOBAL 1.1: System, Audio In).

Specifies the level of the signal immediately after the analog 
audio signal from AUDIO INPUT 1 and 2 is converted into a 
digital signal. Normally you will set this to 127.
If you hear distortion even after lowering this level, it is pos-
sible that the distortion is occurring before the A/D con-
verter. Adjust the [LEVEL] knob or the output level of your 
external sound source so that the “ADC OVER!” indication 
above the “Recording Level” display does not appear.

Sets the panning of the analog audio signal from AUDIO 
INPUT 1 and 2. Normally you will set Input 1 to L000 and 
Input 2 to R127. This allows you to sample a stereo audio 
source in stereo (☞For example settings, p.91, BG p.85).

Select s the bus.

 Select this when you wish to sample the incoming ana-

log audio signal without applying an insert effect. Normally 
you will select L/R.
IFX

: Select this when you want to apply the insert effect to 

the analog audio input signal while it is being sampled. 
(☞p.158)
Off: 

The analog audio signal will not be input.

These settings determine the initial state of the indexes that 
are created when you press the [F6] (“CREATE”) key (1.1–
1c, 4.1–1c). Each new index will be created according to the 
settings you make here, but you are free to modify the set-
tings later.

Specifies whether the new index will be created at the right 
or left of the selected index.

 (Right): The new index will be created at the right of the 

currently selected index.
L

 (Left): The new index will be created at the left of the cur-

rently selected index.

Specifies the key range of the zone of the newly created 
index.

: A single note of the keyboard will be the index. The 

sample of the index will sound at its original key when you 
play that note. This setting can be used similarly to pad 
(keyboard) type samplers.
002...127:

 The sample will change pitch in semitone steps 

across the specified number of keys, centered on the original 
key “Orig.K” (1.1–1b, 4.1–1b). If “Constant Pitch” (4.1–2a) is 
checked

, the pitch will not change.

Specifies where the original key will be located in the zone 
(specified by “Zone Range”) for a newly created index.

(Bottom): The lowest key in the zone will be the origi-

nal key.
Cntr 

(Center): The middle key in the zone will be the origi-

nal key.
Top:

 The top key in the zone will be the original key.

  The recorded sample will automatically be 

played with looping turned on (☞“3.1: Loop Edit”).

Specifies the output destination of the metronome sound 
played by “Count Down” (1.1–2b).

 The metronome will be output from OUTPUT (MAIN) 

L/MONO, R, and the headphones.
1, 2:

 The metronome will be output from OUTPUT (INDI-

VIDUAL) 1 or 2 respectively.

Specifies the level of the metronome sound played by 
“Count Down.”

Adjusts the signal level at the final stage of sampling (☞1.1–
2c).

■

For details on how to select the desired utility function, refer 
to “PROG 1.1–1c: UTILITY.”

1.1–3a

1.1–3b

1.1–3c

1.1–3e

1.1–3f

1.1–3d