Korg Electric Keyboard ユーザーズマニュアル

The following table shows the parameters related to the 
level settings:

*2

*1

:Some effects may not have these parameters.

*2

:Use this parameter to set the Audio Input Level in all 

modes other than Sampling mode.

(IFX) have a stereo input and a stereo output. 

If you select Dry (no effect) for the “W/D” parameter, the 
stereo input signal will be output in stereo without being 
processed by the effect. If you select Wet (effect applied), the 
processed signal will be output in one of the following ways:

If you select 00: No Effect, stereo input signals are output in 
stereo without being processed.
The possible routing of effect inputs and outputs is indi-
cated in the upper left corner of the block diagram.

These can be switched on/off by the “On/Off” settings in 
7.1: Ed-InsertFX (or Insert FX), Setup pages IFX in each 
mode. When off, the effect will be bypassed. In the same 
way as for 00: No Effect, the stereo input sound will be out-
put in stereo without modification.

Separately from this “On/Off” setting, MIDI control 
change CC#92 can be received to turn all IFX effect off. 
A value of 0 is off, and a value of 1–127 restores the 
original setting. You can also use “FX SW” (GLOBAL 
1.1–1b) to turn off IFX in the same way. This is con-
trolled on the global MIDI channel “MIDI Channel” 
(GLOBAL 2.1–1a).

Use “BUS Select” (PROG 7.1–1a) to set the destination bus of 
the oscillator output.

The signal is not sent to the Insert Effects. Instead, it is 

sent to AUDIO OUTPUT (MAIN) L/MONO and R after the 
Master EQ.
IFX:

 The signal is sent to Insert Effect IFX.

 The signal is sent to AUDIO OUTPUT (INDIVID-

UAL) 1, 2 (☞p.162 “Individual Outputs”). The signal is not 
sent to the Insert Effect, Master Effects, and or Master EQ.
Off: 

The signal is not sent to AUDIO OUTPUT (MAIN L/

MONO, R, (INDIVIDUAL) 1 or 2. (After the Master Effects, 
the signal is output to AUDIO OUTPUT (MAIN).) Select this 
option if you connect the Insert Effect with the Master 
Effects in series, with the send level specified by “MFX1 
Send1”and “MFX2 Send2.”

Input

OSC1/2 High, Low Level

(PROG 2.1)

Filter1/2 Trim

(PROG 4.1, 4.2)

Amp1/2 Level

(PROG 5.1, 5.2)

OSC1/2 Send1/2

(PROG 7.1)

Effect Trim parameter

 *1

(PROG 7.1, 7.2)

Output

Effect W/D parameter

(PROG 7.1, 7.2)

Rtn1/2 (Return1, 2)

(PROG 7.2)

Input

Volume 

(COMBI 1.1, 2.1)

S1/2 (Send1/2)

(COMBI 7.1)

Effect Trim parameter 

*1

(COMBI 7.1, 7.2)

Output

Effect W/D parameter

(COMBI 7.1, 7.2)

Rtn1/2 (Return1, 2)

(COMBI 7.2)

Input

Volume 

(SEQ 1.1)

S1/2 (Send1/2)

(SEQ 7.1)

Effect Trim parameter 

*1

(SEQ 7.1, 7.2)

Output

Effect W/D parameter

(SEQ 7.1, 7.2)

Rtn1/2 (Return1. 2)

(SEQ 7.2)

Input

Rear panel AUDIO INPUT LEVEL

Input1/2 Lvl (Level)

(SMPL 1.1)

Effect Trim parameter 

*1

(SMPL 7.1)

Output

Effect W/D parameter

(SMPL 7.1)

Input

Rear panel AUDIO INPUT LEVEL

Input1/2 (Level)

(GLOBAL 1.1)

Input1/2 Send1/2

(GLOBAL 1.1)

+

+