Korg Electric Keyboard ユーザーズマニュアル

This stereo delay uses an LFO to sweep the delay time. The 
pitch also varies. You will obtain a delay sound with swell 
and shimmering. You can also control the delay time using a 
modulation source.

When the modulation source is used for control, this parameter 
reverses the left and right modulation direction.

The LFO can be reset via a modulation source.
The “Src” parameter sets the modulation source that resets the 
LFO. For example, you can assign Gate as a modulation source so 
that the sweep always starts from the specified point.
“L Phase” and “R Phase” set the phase obtained when the left and 
right LFOs are reset. In this way, you can create changes in pitch 
sweep for the left and right channels individually.

The effect is off when a value of the modulation source spec-
ified in the “Src” parameter is 63 or smaller, and the effect is 
on when the value is 64 or higher. The LFO is triggered and 
reset to the “L Phase” and “R Phase” settings when the 
value changes from 63 or smaller to 64 or higher.

This stereo delay controls the level of delay according to the 
input signal level. You can use this as a ducking delay that 
applies delay to the sound only when you play keys at a high 
velocity or only when the volume level is low.

This parameter selects no level control, delay output control 
(effect balance), or feedback amount control.

a

Mod Mode (Modulation Mode)

LFO, Dmod

Switches between LFO modulation control and modulation source 
control

Src (Source)

Off...Tempo

Selects the modulation source that controls delay time

b

Dmod
Reversed L/R control by modulation source

L/R:+/+, L/R:+/–

 

☞

,

Respons (Response)

0...30

Sets the rate of response to the modulation source

c

LFO Wave (LFO Waveform)
Selects LFO Waveform

Tri, Sine

Shape (LFO Shape)

–100...+100

Determines how much the LFO waveform is changed

☞

 Fx:20

d

LFO Freq (LFO Frequency)
Sets the LFO speed

0.02...20.00Hz

e

LFO Sync
Switches LFO reset off/on

Off, On

☞

,

Src (Source)

Off...Tempo

Selects the modulation source that resets the LFO

f

L Phase (L LFO Phase)

–180...+180

Sets the phase obtained when the left LFO is reset

☞

R Phase (R LFO Phase)

–180...+180

Sets the phase obtained when the right LFO is reset

☞

g

L Depth
Sets the depth of the left LFO modulation

0...200

R Depth
Sets the depth of the right LFO modulation

0...200

h

L Dly (L Delay Time)
Sets the left delay time

0.0...500.0

R Dly (R Delay Time)
Sets the right delay time

0.0...500.0

i

L Fb (L Feedback)
Sets the feedback amount of left delay

–100...+100

R Fb (R Feedback)
Sets the feedback amount of right delay

–100...+100

j

W/D (Wet/Dly)

–Wet...–1:99, Dry, 1:99...Wet

☞

 Fx:10,

(Source)

Off...Tempo

(Amount)
Sets the modulation amount of the effect balance

–100...+100

a

Ctrl Target (Control Target)
Selects from no control, output, and feedback

None, Out, FB

☞

Pol (Polarity)
Reverses level control

+, –

☞

b

Threshold
Sets the level to which the effect is applied

0...100

☞

Offset
Sets the offset of level control

0...100

☞

c

Attack
Sets the attack time of level control

1...100

☞

Release
Sets the release time of level control

1...100

☞

d

L Delay (L Delay Time)
Sets the delay time for the left channel

0.0...680.0ms

e

R Delay (R Delay Time)
Sets the delay time for the right channel

0.0...680.0ms

f

Feedback
Sets the feedback amount

–100...+100

g

HiDamp (High Damp) 
Sets the damping amount in the high range

0...100%

☞

 Fx:43

LoDamp (Low Damp)
Sets the damping amount in the low range

0...100%

☞

 Fx:43

h

Spread

–100...+100

Sets the width of the stereo image of the effect sound

☞

 Fx:43

i

W/D (Wet/Dly)

Dry, 1:99...99:1, Wet

(Source)

Off...Tempo

(Amount)
Sets the modulation amount of the effect balance

–100...+100

+