Korg Electric Keyboard ユーザーズマニュアル
Ef
fect
199
67: Comp–Cho/Fl
(Compressor – Chorus/Flanger)
This effect combines a mono-type compressor and a chorus/
flanger. You can change the order of the effect connection.
flanger. You can change the order of the effect connection.
g: Out, h: [Routing]
When Wet Inv is selected, the right channel phase of the chorus/
flanger effect sound is inverted. This creates pseudo-stereo effects
and adds spread.
However, if a mono-input type effect is connected after this effect,
the left and right sounds may cancel each other, eliminating the
chorus/flanger effects.
When “[Routing]” is set to CH/FL
flanger effect sound is inverted. This creates pseudo-stereo effects
and adds spread.
However, if a mono-input type effect is connected after this effect,
the left and right sounds may cancel each other, eliminating the
chorus/flanger effects.
When “[Routing]” is set to CH/FL
→
CMP
, “Out” will be set to
Normal
.
68: Comp–Phaser
(Compressor – Phaser)
This effect combines a mono-type compressor and a phaser.
You can change the order of the effect connection.
You can change the order of the effect connection.
g
C/F W/D (Cho/Flng Wet/Dry)
Sets the center frequency for Band 3
Sets the center frequency for Band 3
300...10.00kHz
Q
Sets the bandwidth of Band 3
Sets the bandwidth of Band 3
0.5...10.0
☞
Fx:06
G (Gain)
Sets the gain of Band 3
Sets the gain of Band 3
–18...+18dB
h
B4 (Band4 Cutoff)
Sets the center frequency for Band 4
Sets the center frequency for Band 4
500...20.00kHz
Q
Sets the bandwidth of Band 4
Sets the bandwidth of Band 4
0.5...10.0
☞
Fx:06
G (Gain)
Sets the gain of Band 4
Sets the gain of Band 4
–18...+18dB
i
W/D (Wet/Dly)
Dry, 1:99...99:1, Wet
(Source)
Off...Tempo
–100...+100
a
[CMP] Sensitivity
Sets the sensitivity
Sets the sensitivity
1...100
☞
Fx:02
b
Attack
Sets the attack level
Sets the attack level
1...100
☞
Fx:02
Level (Output Level)
Sets the compressor output level
Sets the compressor output level
0...100
☞
Fx:02
c
Pre EQ Trim
Sets the EQ input level
Sets the EQ input level
0...100
d
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ
Sets the gain of Low EQ
–15...+15dB
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ
Sets the gain of High EQ
–15...+15dB
e
[CH/FL] LFO (LFO Waveform)
Selects the LFO waveform of the chorus/flanger
Selects the LFO waveform of the chorus/flanger
Tri, Sine
F (LFO Frequency)
Sets the LFO speed
Sets the LFO speed
0.02...20.00Hz
f
Dly (Delay Time)
Sets the delay time
Sets the delay time
0.0...50.0ms
Dep (Depth)
Sets the depth of LFO modulation
Sets the depth of LFO modulation
0...100
Fb (Feedback)
Sets the feedback amount
Sets the feedback amount
–100...+100
☞
Fx:20
g
[F] Cho/Flng W/D
–Wet...–2:98, Dry, 2:98...Wet
Sets the effect balance of the chorus/flanger
☞
Fx:10, 20
Out (Output Mode)
Normal, Wet Inv
Selects the output mode for the chorus/flanger
☞
h
[Routing]
CMP
→
CF/FL, CH/FL
→
CMP
Switches the order of the compressor and chorus/flanger connection
☞
i
W/D (Wet/Dly)
Dry, 1:99...99:1, Wet
(Source)
Off...Tempo
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
Chorus/Flanger
Chorus/Flanger
Feedback
LFO: Tri / Sine
Cho/Flng Wet / Dry
Normal
Wet Invert
Output Mode
–
+
LEQ HEQ
EQ Trim
Comp
Output Level
Envelope - Control
a
[CMP] Sensitivity
Sets the sensitivity
Sets the sensitivity
1...100
☞
Fx:02
b
Attack
Sets the attack level
Sets the attack level
1...100
☞
Fx:02
Level (Output Level)
Sets the compressor output level
Sets the compressor output level
0...100
☞
Fx:02
c
Pre EQ Trim
Sets the EQ input level
Sets the EQ input level
0...100
d
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ
Sets the gain of Low EQ
–15...+15dB
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ
Sets the gain of High EQ
–15...+15dB
e
[PHS] LFO (LFO Waveform)
Selects the LFO waveform of the phaser
Selects the LFO waveform of the phaser
Tri, Sine
F (LFO Frequency)
Sets the LFO speed
Sets the LFO speed
0.02...20.00Hz
f
Manu (Manual)
Sets the frequency to which the effect is applied
Sets the frequency to which the effect is applied
0...100
Dep (Depth)
Sets the depth of LFO modulation
Sets the depth of LFO modulation
0...100
Res (Resonance)
Sets the resonance amount
Sets the resonance amount
–100...+100
☞
Fx:23
g
Phs W/D (Phaser Wet/Dry)
–Wet...–2:98, Dry, 2:98...Wet
Sets the phaser effect balance
☞
Fx:10, 23
Out (Output Mode)
Normal, Wet Inv
Selects the phaser output mode
☞
Fx:67
h
[Routing]
CMP
→
PHS, PHS
→
CMP
Switches the order of the compressor and phaser connection
☞
Fx:67
i
W/D (Wet/Dly)
Dry, 1:99...99:1, Wet
(Source)
Off...Tempo
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
LEQ
HEQ
EQ Trim
Comp
Output Level
Envelope - Control
Phaser
Phaser
Resonance
LFO: Tri / Sine
Phaser Wet / Dry
Normal
Wet Invert
Output Mode
–
+