Korg Electric Keyboard ユーザーズマニュアル

If you install only DRAM SIMM modules (without installing 
the EXB-SMPL), you will be able to load multisample and 
sample data in Media mode.

DRAM SIMM boards are not a manufacturer option. 
Please purchase commercially-available boards that are 
sold for use in computers.

In order to use the maximum of 64 Mbytes, you will 
need to remove the 16 Mbyte DRAM SIMM that was 
installed when installing the EXB-SMPL, and use two 
32 Mbyte DRAM SIMM modules.

The memory banks and sampling time will depend on 
the capacity of the DRAM SIMM boards you install, 
and on the slot locations. (☞p.90)

• So that static electricity in your body does not damage 

the electronic components, touch the ground wire of a 
grounded device or an unpainted metallic component 
to discharge any static electricity in your body before 
installing an option board. Internal components of this 
instrument and of the option boards may be damaged 
by static electricity.

• Follow the installation procedure, and be sure that each 

part is installed correctly and in the correct orientation.

• Please use care in handling option boards. Dropping 

them or applying pressure to them may damage the 
components.

• Avoid touching exposed metal edges of the circuit 

board, or portions that need not be handled during 
installation.

• All screws (and washers) that are removed will be 

used, so be careful not to misplace them.

• Do not use screws other than those that are installed in 

the option board and this instrument. Using screws of a 
different shape or length may damage the unit or cause 
it to malfunction.

• Be sure to firmly tighten the screws used for attach-

ment.

• Be sure that the option board is inserted correctly into 

the connector or slot. After installation, be sure to check 
that the board is installed correctly. If the board is not 
inserted all the way, faulty contact or power supply 
shorts can occur, making the unit malfunction.

• Be careful not to drop parts or the option board into the 

inside of the instrument.

If you are unable to retrieve a screw or part that was 
dropped inside the instrument, please contact your 
local Korg distributor.

Before you perform the installation, be sure to read the 
foregoing section “Please note when installing an 
option board/memory.”

During the installation, be careful not to cut your hand 
on any sharp edges of the TRITON Le or of the option 
board/memory.

1

The EXB-SMPL sampling upgrade contains the following 
items. Make sure that no items are missing.

• EXB-SMPL (board)

: 1 board

• 16 Mbyte DRAM SIMM

: 1 module

• Screws, 3 mm 

×

 8 mm

: 3 screws

2

You will need a “+” (plus) screwdriver, and some maga-
zines or other material (to prevent damage to the joystick 
and knobs etc.: see diagram below)

3

Turn off the TRITON Le, and disconnect the AC/AC 
power supply cable and any other cables by which other 
devices are connected.

4

As shown in the following diagram, place four maga-
zines etc. at the four corners of the instrument to prevent 
damage to the joystick and knobs, and place the 
TRITON Le upside down on top of them.

When turning the TRITON Le upside down, be careful 
not to loose your balance and drop the instrument.

5

Detach the appropriate cover for the option board/mem-
ory you wish to install.

When installing the EXB-SMPL, detach cover “A.” When 
installing the DRAM SIMM, detach cover “B.”

(☞Detaching the cover is described in the following sec-
tions “2–1” or “2–2.”)

View from below

Place in each of the four corners so that joystick and knobs are not contacted

Cover “A”

Cover “B”