Honeywell 62-0342-01 ユーザーズマニュアル

3

62-0342—01

removed. The third-party meter IDR uses a DIP switch to 

perform this function. This switch is preset at the factory and 

requires no further adjustment.

Once you have connected meter #1 to jack #1 in the IDR, the 

IDR should be energized. If the IDR is not energized, verify:

1. Meter #1 is turned on. (Meter #1 powers the IDR; if 

Meter #1 is not installed and powered up, the IDR will 

not function.)

2. Verify that JMP8 on the IDR circuit board has a jumper 

installed.

3. Verify that J23 & J24 on the IDR circuit board are set in 

the position labeled “MTR”. Both jumpers should be set 

to the RIGHT position.

4. Verify that the cable between Meter #1 and Jack #1 on 

the IDR is properly assembled. (See Appendix A for 

cable assembly.)

NOTE: If the IDR is being powered by the optional AC 

adapter instead of by Meter #1, see Section 5.0.

Verify the status of the LED indicators on the IDR circuit 

board. (See Appendix B for locations.)

1. Power Supply Indicators

—

L3, green -> This LED is ON.

—

L1, green -> This LED is ON.

2. System status indicators

—

D4 (CPU), red -> This LED flashes once per sec-

ond. If D4 flashes twice per second, the IDR is not 

initialized. This will be addressed later using E-

Mon Energy software.

—

D7 (Low Battery) -> This LED must be OFF. This 

LED indicates a low or missing battery.

—

D6 (System Error) -> This LED must be OFF.

3. Meter pulse indicators

—

Yellow LEDs P1 through P8 may be flashing. 

These LEDs indicate each meter’s pulse rate. 

The flash rate depends on how much load the 

meter is measuring. The faster the pulse the 

greater the load.

NOTE: If one of the LEDs does not flash, verify the meter 

connection first. If the meter is properly connected, 

check the meter’s display for a flashing load indica-

tor.

4. Panel Indicators

—

Two LEDs are visible through the window on the 

door of the stand-alone enclosure. THESE LEDS 

ARE NOT PRESENT IN MMU STYLE IDRS.

—

Green LED (Power Indicator) -> The green LED 

indicates that power is present at the IDR.

—

Red LED (Tamper Alarm) -> The red LED indi-

cates that the IDR door has been opened. This 

tamper alarm LED will be on when the door is 

closed, and will flash when the door is open. 

When the software startup is performed, the IDR 

will be initialized by the E-Mon Energy software 

and the alarm LED will turn off as long as the door 

remains closed. The alarm can only be reset 

through the software.

5. IDR 16 Option 16 Card (applies only to the SUBIDR-16 

model.)

—

For each meter (9-16) installed on the options 

card, another set of yellow LEDs (P9-P16) will be 

present. These LEDs indicate the meter pulse 

rate for meters #9 through #16.

If you are NOT using the optional AC adapter to power the 

IDR, proceed to Section 6.0.

Instead of powering the IDR using Meter #1, Honeywell can 

supply an optional AC adapter. If the IDR was provided with 

this option, verify the following:

1. Jumpers J23 & J24 on the IDR circuit board are set to 

the LEFT position (position labeled “EXT”.)

2. Jumper at JMP8 MUST be removed.

3. The AC adapter’s two-wire cord must be plugged into 

the IDR at TB9. (The polarity of these wires does not 

matter.)

4. Plug the AC adapter into a 120 VAC outlet.