Sharp TINSE2026QSZZ ユーザーズマニュアル
114
SYSTEM SETTINGS (ADMINISTRATOR)
ENABLE EtherTalk
This program must be enabled to use the machine on
a network that uses EtherTalk protocol.
This program is initially enabled (factory default setting).
a network that uses EtherTalk protocol.
This program is initially enabled (factory default setting).
ENABLE NetBEUI
This program must be enabled to use the machine on
a network that uses NetBEUI protocol.
This program is initially enabled (factory default
setting).
a network that uses NetBEUI protocol.
This program is initially enabled (factory default
setting).
RESET THE NIC
This program is used to restore all network settings to
the factory default settings.
the factory default settings.
INITIALIZE AND/OR STORE SETTINGS
(When the PRINTER EXPANSION KIT is installed)
These programs are used to return the configuration
settings (See the online manual for network printer)
and the "PRINT SETTINGS" (p.111) to the factory
default settings. The programs are also used to store
the current settings and to restore stored settings.
"INITIALIZE AND/OR STORE SETTINGS" consists of
the following programs:
settings (See the online manual for network printer)
and the "PRINT SETTINGS" (p.111) to the factory
default settings. The programs are also used to store
the current settings and to restore stored settings.
"INITIALIZE AND/OR STORE SETTINGS" consists of
the following programs:
● RESTORE FACTORY DEFAULTS
● STORE CURRENT CONFIGURATION
● RESTORE CONFIGURATION
RESTORE FACTORY DEFAULTS
This program is used to return the configuration
settings (see the online manual for network printer)
and the "PRINT SETTINGS" (p.111) to the factory
default settings. If you need a record of the current
settings before restoring the factory defaults, use
"Data list print" in the system settings (general) to print
a list of the current settings. (See "4. SYSTEM
SETTINGS (GENERAL)".)
settings (see the online manual for network printer)
and the "PRINT SETTINGS" (p.111) to the factory
default settings. If you need a record of the current
settings before restoring the factory defaults, use
"Data list print" in the system settings (general) to print
a list of the current settings. (See "4. SYSTEM
SETTINGS (GENERAL)".)
STORE CURRENT CONFIGURATION
This program is used to store the current configuration
settings (see online manual for network printer) and
"PRINT SETTINGS" (p.111). The stored settings will
not be erased even if the power is turned off. To
restore the stored settings, use the "RESTORE
CONFIGURATION" program.
settings (see online manual for network printer) and
"PRINT SETTINGS" (p.111). The stored settings will
not be erased even if the power is turned off. To
restore the stored settings, use the "RESTORE
CONFIGURATION" program.
RESTORE CONFIGURATION
This program is used to restore settings that were
stored using the "STORE CURRENT
CONFIGURATION" program.
The current settings will change to the restored
settings.
stored using the "STORE CURRENT
CONFIGURATION" program.
The current settings will change to the restored
settings.
*1
Some programs in the following are marked
by "*1". This indicates that a message will
appear at the end of the setting procedure
asking you to confirm execution of the new
setting. If needed, you can cancel the new
setting by touching the [NO] key.
by "*1". This indicates that a message will
appear at the end of the setting procedure
asking you to confirm execution of the new
setting. If needed, you can cancel the new
setting by touching the [NO] key.
If any of the "NETWORK SETTINGS"
(p.113) were changed before execution of
this program, you must turn off the
machine’s power switch, wait briefly, and
then turn the switch back on in order to
make the settings take effect.
(p.113) were changed before execution of
this program, you must turn off the
machine’s power switch, wait briefly, and
then turn the switch back on in order to
make the settings take effect.
Note
*1
*1
*1
Note
MX-M310.book 114 ページ ２００９年７月６日 月曜日 午後６時５７分