Sharp TINSE2026QSZZ ユーザーズマニュアル
24
COPY FUNCTIONS
COPYING FROM THE RSPF
1
Make sure that an original has not
been left on the document glass and
then close the RSPF.
been left on the document glass and
then close the RSPF.
If an original remains on
the document glass after a
copy was made,
"REMOVE THE
ORIGINAL FROM THE
DOCUMENT GLASS." will
appear in the touch panel.
the document glass after a
copy was made,
"REMOVE THE
ORIGINAL FROM THE
DOCUMENT GLASS." will
appear in the touch panel.
2
Adjust the original guides to the size
of the original.
of the original.
3
Place the originals face up in the
document feeder tray.
document feeder tray.
Insert the originals all the
way into the feed slot.
The original size appears
in the touch panel.
way into the feed slot.
The original size appears
in the touch panel.
4
Make sure that the same size of paper
as the original is selected.
as the original is selected.
The selected tray is
highlighted. If none of the
trays have the same size
of paper as the original,
"LOAD xxxx PAPER."
will appear.
highlighted. If none of the
trays have the same size
of paper as the original,
"LOAD xxxx PAPER."
will appear.
Even if the message above is displayed, copying can
be performed using the selected paper tray.
be performed using the selected paper tray.
5
Select the number of copies and any
other desired copy settings, and then
press the [START] key (
other desired copy settings, and then
press the [START] key (
).
• The number in the copy quantity display will
decrease by 1 each time a copy is made.
• If you are only making a single copy, the copy can be
made with the copy number display showing "0".
• To clear a mistake, press the [CLEAR] key ( ).
Stream feeding mode
If stream feeding mode is enabled in the administrator
settings, "SET ORIGINALS FOR STREAM FEEDING."
will appear in the touch panel for approximately 5
seconds after the originals are fed. Any new originals
placed in the RSPF while this message appears will be
fed and copied automatically.
settings, "SET ORIGINALS FOR STREAM FEEDING."
will appear in the touch panel for approximately 5
seconds after the originals are fed. Any new originals
placed in the RSPF while this message appears will be
fed and copied automatically.
Copying a large number of originals
Job Build mode is useful when you need to copy more
originals that can be placed in the RSPF at once. For
information on Job Build mode, see "JOB BUILD
MODE" (p.46).
originals that can be placed in the RSPF at once. For
information on Job Build mode, see "JOB BUILD
MODE" (p.46).
• If "AUDITING MODE" (p.95) is enabled, enter your 5-digit account number.
• If the RSPF is disabled in the administrator settings, the RSPF cannot be used. See "6. SYSTEM SETTINGS
• If the RSPF is disabled in the administrator settings, the RSPF cannot be used. See "6. SYSTEM SETTINGS
(ADMINISTRATOR)".
Note
• Up to 100 pages (24 lbs. (90 g/m
2
)) can
be inserted at once. The stack of originals
must not be higher than the indicator line
on the tray.
must not be higher than the indicator line
on the tray.
• If the original size is not automatically
detected, manually set the original size.
(p.48)
(p.48)
Note
• To load paper, see "LOADING PAPER"
(p.16). If you change the paper size in the
tray, you will also need to change the
tray's paper size and paper type settings.
(p.20)
tray, you will also need to change the
tray's paper size and paper type settings.
(p.20)
• If needed, manually select the paper tray
that has the desired size of paper as
explained on page 22.
explained on page 22.
• The paper types for the auto paper selection
function can be selected, or the function
disabled, in the administrator settings. (See "6.
SYSTEM SETTINGS (ADMINISTRATOR)".)
disabled, in the administrator settings. (See "6.
SYSTEM SETTINGS (ADMINISTRATOR)".)
• If the original size is larger than the paper
size, the result of copying from the
document glass may differ from the result
of copying from the RSPF. (p.23)
document glass may differ from the result
of copying from the RSPF. (p.23)
• Press the [CLEAR] key (
) to stop
copying in the middle of a run.
• If copying stops because the tray has run
out of paper, you can resume copying by
touching the [PAPER SELECT] key and
selecting the bypass tray or a paper tray
that has the same size and type of paper
loaded in the same orientation.
touching the [PAPER SELECT] key and
selecting the bypass tray or a paper tray
that has the same size and type of paper
loaded in the same orientation.
Note
UT
LOGOUT
Note
MX-M310.book 24 ページ ２００９年７月６日 月曜日 午後６時５７分