Sharp MX-M160D ユーザーズマニュアル
20
BEFORE USING THE PRODUCT
Loading paper in the bypass tray
1
Open the bypass tray.
Pull out the bypass tray
extension to load B4 and A3
(8-1/2" x 14" and 11" x 17") size
paper.
extension to load B4 and A3
(8-1/2" x 14" and 11" x 17") size
paper.
2
Set the bypass tray guides to the
paper width.
paper width.
3
Insert the copy paper (print side
down) all the way into the bypass tray.
down) all the way into the bypass tray.
Make sure that the print side of
the paper is face down.
To prevent a misfeed, verify
once more that the bypass tray
guides are adjusted to the width
of the paper.
the paper is face down.
To prevent a misfeed, verify
once more that the bypass tray
guides are adjusted to the width
of the paper.
Important points when inserting
paper in the bypass tray
paper in the bypass tray
• Up to 100 sheets of standard copy paper can be set
in the bypass tray.
• Be sure to place A6 and B6 (5-1/2" x 8-1/2") size
paper and envelopes horizontally as shown in the
following diagram.
following diagram.
• When loading envelopes, make sure that they are
straight and flat and do not have loosely glued
construction flaps (not the closure flap).
construction flaps (not the closure flap).
• Special papers except SHARP recommended
transparency film, labels, and envelopes must be fed
one sheet at a time through the bypass tray.
one sheet at a time through the bypass tray.
• When adding paper, first remove any paper
remaining in the tray, combine it with the paper to be
added and then reload as a single stack. The paper
to be added must be the same size and type as the
paper already in the tray.
added and then reload as a single stack. The paper
to be added must be the same size and type as the
paper already in the tray.
• Do not use paper that is smaller than the original.
This may cause smudges or unclean images.
• Do not use paper that has already been printed on
by a laser printer or plain paper fax machine. This
may cause smudges or unclean images.
may cause smudges or unclean images.
Envelopes
Do not use the following envelopes, as misfeeds will
occur.
occur.
• Envelopes with metal tabs, clasps, strings, holes, or
windows.
• Envelopes with rough fibers, carbon paper, or glossy
surfaces.
• Envelopes with two or more flaps.
• Envelopes with tape, film, or paper attached to the
• Envelopes with tape, film, or paper attached to the
flap.
• Envelopes with a fold in the flap.
• Envelopes with glue on the flap to be moistened for
• Envelopes with glue on the flap to be moistened for
sealing.
• Envelopes with labels or stamps.
• Envelopes that are slightly inflated with air.
• Envelopes with glue protruding from the seal area.
• Envelopes with part of the seal area peeled off.
• Envelopes that are slightly inflated with air.
• Envelopes with glue protruding from the seal area.
• Envelopes with part of the seal area peeled off.
• If you loaded paper in the bypass tray,
press the [PAPER SELECT] key to select
the bypass tray.
the bypass tray.
• If you load thick paper in the bypass tray,
press the [PAPER] key until "EXTRA" is
highlighted. The paper type is set to thick
paper. The setting is cleared when "Auto
clear" works or the [CA] key is pressed.
For restrictions on paper types and
weights, see "PAPER" (page 18).
highlighted. The paper type is set to thick
paper. The setting is cleared when "Auto
clear" works or the [CA] key is pressed.
For restrictions on paper types and
weights, see "PAPER" (page 18).
Note