Sharp MX-M182D ユーザーズマニュアル
22
2
POWER ON AND OFF
The power switch is located on the left side of the machine.
POWER ON
Turn the power switch to the "ON"
position.
position.
It will take about 25 seconds
for the machine to warm up.
While the machine is
warming up, the START
indicator will blink. (The
START indicator will light up
when the machine is ready
for the machine to warm up.
While the machine is
warming up, the START
indicator will blink. (The
START indicator will light up
when the machine is ready
to copy.)
However, you can make desired settings and press
the [START] key (
However, you can make desired settings and press
the [START] key (
) during warm-up. Copying will
start after warm-up.
POWER OFF
Make sure that the machine is not in
operation and then turn the power switch
to the "OFF" position.
operation and then turn the power switch
to the "OFF" position.
If the power switch is turned
off while the machine is in
operation, a misfeed may
occur and the job that was in
progress will be cancelled.
off while the machine is in
operation, a misfeed may
occur and the job that was in
progress will be cancelled.
Power save modes
The machine has two power save modes to reduce overall power consumption thereby reducing the cost of
operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two
power save modes are "Preheat mode" and "Auto power shut-off mode".
operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two
power save modes are "Preheat mode" and "Auto power shut-off mode".
Preheat mode
This function automatically switches the machine to a low power consumption state if the duration of time set in the
system settings elapses without the machine being used when the power is on. In preheat mode the display turns
off. Normal operation automatically resumes when a key on the operation panel is pressed, an original is placed, or
a print job or fax is received.
system settings elapses without the machine being used when the power is on. In preheat mode the display turns
off. Normal operation automatically resumes when a key on the operation panel is pressed, an original is placed, or
a print job or fax is received.
Auto power shut-off mode
This function automatically switches the machine to a state that consumes even less power than preheat mode if the
duration of time set in the system settings elapses without the machine being used when the power is on. During
auto power shut-off, only the START indicator blinks. To restore the machine to normal operation, press the
[START] key. Normal operation also resumes automatically when a print job or fax is received or scanning is begun
from a computer. While auto power shut-off is in effect, pressing a key other than the [START] key will have no
effect.
duration of time set in the system settings elapses without the machine being used when the power is on. During
auto power shut-off, only the START indicator blinks. To restore the machine to normal operation, press the
[START] key. Normal operation also resumes automatically when a print job or fax is received or scanning is begun
from a computer. While auto power shut-off is in effect, pressing a key other than the [START] key will have no
effect.
Default settings
The machine is set at the factory to return all settings to the default settings one minute after a copy job is finished
(auto clear function) or when the [CA] key is pressed. When the settings return to the default settings, any functions
that were selected are cancelled.
The auto clear time can be changed in the system settings.
(auto clear function) or when the [CA] key is pressed. When the settings return to the default settings, any functions
that were selected are cancelled.
The auto clear time can be changed in the system settings.
In the default state the display shown below appears. The default state of the display may vary depending on
settings in the system settings.
settings in the system settings.
*The screen is that of the MX-M232D.
• The machine reverts to the initial settings when it is first turned on, when the [CA] key is pressed, or when no
keys are pressed for the preset "Auto clear" time following the end of a copy job. When the machine reverts to
the initial settings, all settings and functions selected to that point are cancelled. The "Auto clear" time can be
changed in the system settings.
the initial settings, all settings and functions selected to that point are cancelled. The "Auto clear" time can be
changed in the system settings.
• The machine is initially set to automatically enter power save mode if not used for copying or printing, for a
preset period of time. This setting can be changed in the system settings.
The preheat activation time and the "Auto power shut-off timer" can be changed using system settings. It is
suggested that you set times that are appropriate for your usage of the machine.
suggested that you set times that are appropriate for your usage of the machine.
Note
Note
100%
A4
Ready to copy.
AUTO
AUTO