Sharp MX-M182 ユーザーズマニュアル
121
SYSTEM SETTINGS GUIDE
To turn on the toner save mode, highlight "TONER
SAVE MODE" and press the [OK] key to display a
check mark in the check box.
SAVE MODE" and press the [OK] key to display a
check mark in the check box.
To turn off the toner save mode, select this
program and press the [OK] key again to clear the
check mark in the check box.
program and press the [OK] key again to clear the
check mark in the check box.
COPY SETTINGS
These programs are used to enable various copy
functions. To access one of these programs, select
"COPIER" in the mode selection screen, select the
desired program in the copy settings screen, and
press the [OK] key.
functions. To access one of these programs, select
"COPIER" in the mode selection screen, select the
desired program in the copy settings screen, and
press the [OK] key.
EXPOSURE ADJUST
This program is used to adjust the exposure level
when "AUTO" is used for the exposure mode. The
auto exposure level can be set separately for the
document glass and the SPF/RSPF.
One of five levels can be selected, with the left end of
the scale the lightest level and the right end of the
scale the darkest level.
The factory default setting is the middle level.
when "AUTO" is used for the exposure mode. The
auto exposure level can be set separately for the
document glass and the SPF/RSPF.
One of five levels can be selected, with the left end of
the scale the lightest level and the right end of the
scale the darkest level.
The factory default setting is the middle level.
Select "EXPOSURE ADJUST" and press the [OK] key.
The following screen will appear.
The following screen will appear.
1
Select "PLATEN" or "SPF/RSPF" with the
[
[
] or [
] key.
2
Press the [
] or [
] key to adjust the
exposure.
3
Repeat steps 1 and 2 to adjust the other
exposure.
exposure.
4
Press the [OK] key.
MARGIN DEFAULT
(When the dual function board is installed)
This is used to set the default margin width.
The factory default setting is "10 mm (1/2 inch)".
The factory default setting is "10 mm (1/2 inch)".
Select "MARGIN DEFAULT" and press the [OK] key.
The following screen will appear.
The following screen will appear.
1
Adjust the default margin width with the
[
[
] or [
] key.
The width can be set from 0 to 20 mm in
increments of 5 mm (0" to 1" in increments of 1/4").
increments of 5 mm (0" to 1" in increments of 1/4").
2
Press the [OK] key.
ERASE ADJUST
(When the dual function board is installed)
This is used to set the default erasure width.
The factory default setting is "10 mm (1/2 inch)".
The factory default setting is "10 mm (1/2 inch)".
Select "ERASE ADJUST" and press the [OK] key. The
following screen will appear.
following screen will appear.
1
Adjust the edge erase and centre erase
width with the [
width with the [
] or [
] key.
The edge erase width and the centre erase width
share the same default value, which can be set
from 0 to 20 mm in increments of 5 mm (0" to 1" in
increments of 1/4").
share the same default value, which can be set
from 0 to 20 mm in increments of 5 mm (0" to 1" in
increments of 1/4").
2
Press the [OK] key.
ID CARD SETTING
The layout pattern for copying of the ID card can be
changed during the ID card copy process.
Refer to the illustration in "ID CARD COPY"
changed during the ID card copy process.
Refer to the illustration in "ID CARD COPY"
for
the available layout patterns.
Select "ID CARD COPY" and press the [OK] key. The
following screen will appear.
following screen will appear.
1
Press the [
] or [
] key to select a layout
pattern.
2
Press the [OK] key.
EXPOSURE ADJUST
PLATEN
SPF/RSPF
(0~20)
MARGIN DEFAULT
mm
(0~20)
ERASE ADJUST
mm
ID CARD SETTING
A4 SIZE
A5-A3 SIZE