Sharp MX-M700U ユーザーズマニュアル
0-5
CONTENTS
Page
OPERATION MANUALS .............................................. 0-1
INSTALLATION REQUIREMENTS............................... 0-2
CAUTIONS................................................................... 0-3
INSTALLATION REQUIREMENTS............................... 0-2
CAUTIONS................................................................... 0-3
● Laser Information ................................................. 0-4
INTRODUCTION.......................................................... 1-2
MAIN FEATURES ........................................................ 1-3
PART NAMES AND FUNCTIONS................................ 1-10
MAIN FEATURES ........................................................ 1-3
PART NAMES AND FUNCTIONS................................ 1-10
● Operation panel.................................................... 1-13
● Touch panel.......................................................... 1-14
TURNING THE POWER ON AND OFF ....................... 1-17
AUDITING MODE ........................................................ 1-18
AUDITING MODE ........................................................ 1-18
enabled................................................................. 1-18
LOADING PAPER ........................................................ 2-2
● Identifying the trays .............................................. 2-2
● Loading paper in paper tray 1 - tray 2 .................. 2-2
● Loading paper in paper tray 3 .............................. 2-5
● Changing the paper size in paper tray 3 .............. 2-5
● Changing the paper size in paper tray 4 .............. 2-6
capacity tray AR-LC6) ..................................................2-7
capacity tray AR-LC7) ..................................................2-8
● Loading paper in the bypass tray ......................... 2-10
paper that can be used in the trays) ..................... 2-12
● Setting the paper type and paper size.................. 2-14
SYSTEM SETTINGS ................................................... 2-18
● General procedure for system settings ................ 2-18
● About the settings ................................................ 2-20
REPLACING THE TONER CARTRIDGES .................. 2-21
STORAGE OF SUPPLIES ........................................... 2-22
MISFEED REMOVAL ................................................... 2-23
STORAGE OF SUPPLIES ........................................... 2-22
MISFEED REMOVAL ................................................... 2-23
● Misfeed removal guidance.................................... 2-23
● Misfeed in the duplex unit..................................... 2-25
● Misfeed in the paper feed area............................. 2-26
REMOVING AN ORIGINAL MISFEED......................... 2-31
document feeder .................................................. 2-31
TROUBLESHOOTING ................................................. 2-32
FINISHER AND SADDLE STITCH FINISHER .............3-2
● Part names ...........................................................3-2
● Specifications .......................................................3-2
● Finishing methods ................................................3-4
● Finishing modes and finisher functions ................3-6
● Removing a misfeed .............................................3-11
● Part names ...........................................................3-14
● Specifications .......................................................3-14
● Loading paper.......................................................3-15
● Manual operation of the inserter...........................3-15
● Misfeed removal ...................................................3-17
● Troubleshooting inserter problems .......................3-18
SHARP OSA.................................................................3-19
APPLICATION COMMUNICATION MODULE (MX-
APPLICATION COMMUNICATION MODULE (MX-
● Standard application setup ...................................3-19
● Selecting a standard application...........................3-19
● Operation in OSA mode .......................................3-20
EXTERNAL ACCOUNT MODULE (MX-AMX3)............3-21
● External account application setup.......................3-21
● Operation in external account mode.....................3-21
AUTOMATIC DOCUMENT FEEDER............................4-2
● Acceptable originals .............................................4-2
PLACING ORIGINALS .................................................4-3
CHECKING THE SIZE OF A PLACED ORIGINAL.......4-5
CHECKING THE SIZE OF A PLACED ORIGINAL.......4-5
● Manually setting the scanning size.......................4-5
● Storing or deleting an original size .......................4-6
NORMAL COPYING.....................................................4-7
feeding function ....................................................4-7
document feeding function....................................4-10
● Copying from the document glass ........................4-11
ADJUSTING THE EXPOSURE ....................................4-14
REDUCTION/ENLARGEMENT/ZOOM ........................4-15
REDUCTION/ENLARGEMENT/ZOOM ........................4-15
● Automatic selection (auto image) .........................4-15
● Manual selection (preset copy ratios/zoom) .........4-16
SPECIAL PAPERS .......................................................4-20