Toshiba 212 ユーザーズマニュアル
Before Calling Service Technician 199
Before Calling Service Technician
When you encounter trouble using this equipment, check the items listed below.
General operation
Phenomenon
Usual cause
Countermeasure
The equipment does not
operate at all.
operate at all.
The power of the equipment
is not turned ON.
is not turned ON.
Turn ON the power of the equipment.
The power cable is not
plugged in securely.
plugged in securely.
Plug in the power cable securely.
The weekly timer functions
and the equipment is in the
sleep mode.
and the equipment is in the
sleep mode.
Press any of the [ENERGY SAVER] but-
ton, the [START] button and the function
switching buttons on the control panel.
ton, the [START] button and the function
switching buttons on the control panel.
The button does not respond
to my operation.
to my operation.
It has been a short time
since the power was turned
ON.
since the power was turned
ON.
Wait for the completion of warm-up and
then try again.
then try again.
The LCD screen is too light/
dark.
dark.
The contrast of the LCD
screen is not adjusted prop-
erly.
screen is not adjusted prop-
erly.
A message is displayed on
the LCD screen.
the LCD screen.
The equipment has detected
an error status.
an error status.
“Enter DEPARTMENT
CODE” appears on the LCD
screen.
CODE” appears on the LCD
screen.
When the use of the equip-
ment is managed under
department management,
and the department code
has not been entered.
ment is managed under
department management,
and the department code
has not been entered.
“Saving energy” appears on
the LCD screen.
the LCD screen.
The equipment is in the low
power mode.
power mode.
The equipment enters into the low power
mode after a specified time has passed
since its last use. Copying is enabled.
mode after a specified time has passed
since its last use. Copying is enabled.
“Sleep mode” appears on the
display.
display.
The equipment is in the
sleep mode.
sleep mode.
The equipment enters into the sleep
mode after a specified time has passed
since its last use. For how to cancel this
mode, see the following page.
mode after a specified time has passed
since its last use. For how to cancel this
mode, see the following page.
The LCD screen is dim.
The equipment is in the
super sleep mode.
super sleep mode.
The equipment enters into the super
sleep mode after a specified time has
passed since its last use. For how to can-
cel this mode, see the following page.
sleep mode after a specified time has
passed since its last use. For how to can-
cel this mode, see the following page.
Scanning stops before it is
finished. (“Count over”
appears on the LCD screen.)
finished. (“Count over”
appears on the LCD screen.)
The number of pages
scanned has exceeded the
maximum value.
scanned has exceeded the
maximum value.
To copy the data scanned so far, select
“Print”. To delete them, select “Cancel
job”.
(If “Print” is grayed out, only data deletion
is possible.)
“Print”. To delete them, select “Cancel
job”.
(If “Print” is grayed out, only data deletion
is possible.)
Scanning stops before it is
finished. (“Memory is full”
appears on the LCD screen.)
finished. (“Memory is full”
appears on the LCD screen.)
The built-in memory of the
equipment has become full.
equipment has become full.
To copy the data scanned so far, select
“Print”. To delete them, select “Cancel
job”.
(If “Print” is grayed out, only data deletion
is possible.)
“Print”. To delete them, select “Cancel
job”.
(If “Print” is grayed out, only data deletion
is possible.)
Copying stops before it is fin-
ished. (“Clear paper output
tray: PRESS START KEY.”
appears on the display.)
ished. (“Clear paper output
tray: PRESS START KEY.”
appears on the display.)
Approx. 250 sheets of paper
have continuously exited and
the equipment stops copy-
ing to prevent the copied
paper from overflowing from
the tray.
have continuously exited and
the equipment stops copy-
ing to prevent the copied
paper from overflowing from
the tray.
Remove the paper from the receiving tray,
and then press the [START] button. Copy-
ing resumes.
Press the [CLEAR/STOP] button to end
the copy job. “Memory clear?” appears on
the LCD screen. Select “YES”, and then
press the [START] or [ENTER] button.
and then press the [START] button. Copy-
ing resumes.
Press the [CLEAR/STOP] button to end
the copy job. “Memory clear?” appears on
the LCD screen. Select “YES”, and then
press the [START] or [ENTER] button.