ColorVision c2630 ユーザーズマニュアル
8-1
Section 8
OPTIONAL EQUIPMENT
Document Processor
Automatically feeds and scans multiple sheet-originals one by one.
Two-sided originals are automatically turned over so that both
sides can be scanned and copied.
Two-sided originals are automatically turned over so that both
sides can be scanned and copied.
Acceptable originals
• Use sheet originals only
• Paper weight
• Paper weight
One-sided originals: Use only originals with a paper weight of
between 35 g/m² and 160 g/m².
Two-sided originals: Use only originals with a paper weight of
between 50 g/m² and 120 g/m².
between 35 g/m² and 160 g/m².
Two-sided originals: Use only originals with a paper weight of
between 50 g/m² and 120 g/m².
• Sizes: 5
1/2
"× 8
1/2
" - 11" × 17" [A5R - A3]
• Number which can be set at one time
100 sheets (11" × 8
1/2
" [A4] size or smaller, between 50 g/m² and
80 g/m²)
70 sheets (8
70 sheets (8
1/2
" × 14" [B4] size or larger, between 50 g/m² and
80 g/m²)
(The maximum number of originals that can be set when using
the auto selection mode is 30 sheets.)
(The maximum number of originals that can be set when using
the auto selection mode is 30 sheets.)
Notes on acceptable documents
Be sure NOT to use the following as originals in the Document
Processor:
• OHP film and other transparencies
• Carbon paper, crumpled originals or originals with strong folds,
Processor:
• OHP film and other transparencies
• Carbon paper, crumpled originals or originals with strong folds,
and soft originals such as vinyl
• Originals which are not rectangular, wet originals, and originals
with adhesive tape or glue
• Originals with clips or staples (In order to use such originals,
remove the clips or staples and straighten any crumples or folds
before using them. Failure to do so may cause originals to
misfeed.)
before using them. Failure to do so may cause originals to
misfeed.)
• Clippings or originals with very slippery surfaces
• Originals with wet correction fluid
• Originals with folds (If you must use such originals, smooth out
• Originals with wet correction fluid
• Originals with folds (If you must use such originals, smooth out
the folded portions before setting them in the Document
Processor. Failure to do so may cause originals to misfeed.)
Processor. Failure to do so may cause originals to misfeed.)
Names of parts
(1) Original table
Set originals to be copied on this table.
(2) Original insert guides
Align these guides to fit the width of the originals to be copied.
(3) Left cover
Open this cover if an original misfeed occurs.
(4) Original eject table
Originals that have been copied are ejected and stored here.
(5) Ejection extension
Open this extension when using larger sized originals such as
8
8
1/2
" × 14" and 11" × 17" [B4 and A3].
(6) Document Processor release lever
Operate this lever when you want to open the Document
Processor.
Processor.
(7) Original set indicator
Indicates the status of originals set in the Document
Processor.
Lit green: The originals are set properly. Copying will begin
when you press the [Start] key.
Blinking green: The originals need to be reset.
Blinking red: An original has jammed. See page 9-16 and
removed the jammed original.
Processor.
Lit green: The originals are set properly. Copying will begin
when you press the [Start] key.
Blinking green: The originals need to be reset.
Blinking red: An original has jammed. See page 9-16 and
removed the jammed original.