JVC 0110SKH-MW-MT ユーザーズマニュアル

Solutions to common problems related to the monitor are described here. If none of the solutions presented here 
solve the problem, unplug the monitor and consult an authorized dealer or service center.

• Press the 

 button.

•  Firmly insert the AC power plug.
•  Turn on the POWER switch on the rear panel.

6
8
8

•  Select the correct input using the INPUT SELECT buttons. 
•  Connect the signal cable firmly.
•  Turn on the power of the connected component and set the output 

correctly.

•  Check whether the input signal format is acceptable on the monitor.

6
8

—

10, 11

•  Adjust the volume level.
•  Deactivate the muting function.
•  Connect the signal cable firmly. 
•  Turn on the power of the connected component and set the output 

correctly.

6
6
8

—

•  Check whether the input signal format is acceptable on the monitor.

10, 11

•  Select the correct input using the INPUT SELECT buttons.
•  Connect the signal cable firmly. 
•  Turn on the power of the connected component and output video 

signals. Or, check whether the video output of the component (video 
output setting of the VCR or graphic board of the computer) is set 
correctly.

6
8

—

•  Adjust each picture adjustment knob on the front panel or adjust the 

items of “PICTURE SUB ADJ.” in the SET-UP MENU. Or, perform 
“reset” in “PICTURE SUB ADJ.” 

•  Check whether the setting of COLOR OFF or SCREENS CHECK 

buttons are appropriate.

•  Select the proper color system (“COLOR SYSTEM”) in “FUNCTION 

SETTING” of the SET-UP MENU.

•  Adjust the items of “WHITE BALANCE SET.” in the SET-UP MENU. 

Or, perform “reset” in “WHITE BALANCE SET.”

6, 16

6

16

17

•  When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has 

changed. Though the remaining picture will disappear after a while, there may be a case that it remains 
for a long period depending on the length of time the still image was displayed for. This is due to the 
characteristics of the LCD display and is not a malfunction.

•  Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays, 

and not a problem. The LCD display is built with very high precision technology; however, be aware that a 
few pixels may be missing or constantly lit.

•  The following symptoms are problems only when pictures or sounds are not played back normally.

– A slight electric shock occurs when you touch the monitor.
– The top and/or rear panel of the monitor becomes hot.
– The monitor emits a cracking noise.
– The monitor emits a mechanical noise.

•  Adjust the picture contrast or brightness by using the adjustment 

knobs on the front panel. Or, adjust “CONTRAST” or “BRIGHT” of 
“PICTURE SUB ADJ.” in the SET-UP MENU. 

6, 16

•  Check whether the setting of 1:1 or ASPECT buttons is appropriate.
•  Check whether the input signal format is acceptable on the monitor.
•  Adjust the picture size (H SIZE/V SIZE) or position (H POSITION/V 

POSITION) of “SIZE/POSI. ADJ.” in the SET-UP MENU.

•  For some signals, the picture cannot be displayed fully in the effective 

screen area. There is no sure method to solve this problem.

6

10, 11

17

—

•  The items which are not available for the current input or the current 

input signal are not displayed on the menu. Change the input or the 
input signal.

•  The items controlled by the MAKE system do not appear on the 

menu.

—

20

•  Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”
•  You cannot use the buttons for the items controlled by the MAKE 

system. Disable the external control.

19

20, 21

DT-V24G1_20L3G_EN.indd   24

DT-V24G1_20L3G_EN.indd   24

10.1.15   3:22:27 PM

10.1.15   3:22:27 PM