JVC DT-V9L5 ユーザーズマニュアル

27

27

“No Effect” is displayed when you press a button which is not 

• 

available for the current input or signal format (the lamp lights 
even when the function does not actually work).
The items controlled by the MAKE system cannot be controlled 

• 

by the buttons on the front panel (“Remote On” is displayed 
and the lamps do not light).

Tally lamp
This lamp is controlled by the tally function of the MAKE/TRIGGER 
terminal.

You can select the color of the tally lamp from “Green” or “Red.” 

• 

You can also select whether the whole lamp is turned on at once, 
or whether it is turned on one half at a time. (

☞ “Tally Setting” on 

page 37 and “External Control” on page 42)

1 Screw holes for attaching protective filter (provided)

Attach the protective filter by using the provided screws.

●

 Attach the filter to the LCD panel with the frosted side of the 

filter facing outwards (when the monitor is shipped from the 
factory, protective films are attached to both sides, and a sticker 
is attached to the frosted side. Remove the protective films 
before use).

●

 Use only the provided screws to avoid damaging the monitor.

●

 When attaching the protective filter, do not fasten screws too 

tightly; otherwise, the protective filter may be damaged.

2 Speaker (monaural) (DT-V9L5 only)

Outputs the mixed audio of the AUDIO OUT1 terminal and AUDIO 
OUT2 terminal. (

☞ 9 on page 29)

3 Headphones jack (stereo)

Outputs the same audio signal as that output from the 
AUDIO(MONITOR OUT) terminals.(

☞ 9 on page 29)

4 Picture adjustment knob

PHASE: 

Adjusts the picture hue.

CHROMA: 

Adjusts the picture color density.

BRIGHT: 

Adjusts the picture brightness.

CONTRAST: 

Adjusts the picture contrast.

●

 PHASE and CHROMA cannot be adjusted for certain signal 

formats.

●

 When “Component Phase” is set to “Disable” and an NTSC signal 

is input, PHASE can be adjusted. (

☞ page 38)

5  MUTING button

Turns off the sound of the speaker(DT-V9L5 only) and of the 
headphone. (muting)

●

 To cancel the function, press the button again.

●

 Muting function is also canceled when the volume is adjusted.

(

☞ page 30)

●

 Muting function cannot be activated when a menu screen is 

displayed.

6    /   /   /   buttons

When a menu screen is displayed selects or adjusts menu items. 
(

☞ “The operation procedure” on page 31)

7 SCR. CHK. (Screens check) button/lamp

Displays only the selected element (R, G, B, or the luminance) of 
video signal.

●

 Each time you press this button, the screen changes in the 

following order.

Normal screen

Red screen

Green screen

Blue screen

Monochrome screen

8 MARKER button/lamp

Displays/hides the area marker and the safety marker.

●

 Select the size and the style of the markers in “Marker” of the 

Main Menu (

☞ page 34).

●

 The marker is not displayed when it is set to “Off” in “Marker”. 

(

☞ page 34)

9 INPUT SELECT buttons/lamps

Selects an input.
SDI 1: 

 E. AUDIO HD/SD SDI (IN 1) terminal

SDI 2: 

 E. AUDIO HD/SD SDI (IN 2) terminal

VIDEO/COMPO.: VIDEO/COMPONENT terminal
HDMI: HDMI 

terminal

●

 The lamp for the selected input lights.

p Power lamp

The lamp lights as described below.
Unlit: 

   The monitor is completely off (the power switch 

on the rear panel is turned off).

 

   In Low Power Mode (

☞ page 41)

Lights in green:    The monitor is on.
Lights in orange:  The monitor is off (on standby).
Flashes in orange:   The monitor is in the Power Save (power save) mode. 

(

☞ “No Sync Action” in “Sync Function” on page 36)

q 

Turns on and off (on standby) the monitor.

●

 The power switch is equipped on the rear panel of the monitor. 

(

☞ 1 on page 28 and 3 on page 29)

w FUNCTION button

Assign functions to the F1 button when the menu is not displayed. 

(

☞ page 37)

e VOLUME adjustment button/EMBEDDED AUDIO setting 

button
Adjusts the volume when no menu screen is displayed.
Selects an audio channel when EMBEDDED AUDIO signals are 
contained in SDI input. (

☞ “Volume Adjustment/Audio Channel 

Selection” on page 30)

r MENU button

Activates/deactivates the display of the Main Menu. (

☞ “The 

operation procedure” on page 31)

t F1 button/lamp

You can use the functions assigned to this button.

The illustration of the 
monitor is of DT-V9L5.

3 - y are common 
to DT-V9L5 and 
DT-F9L5. 
The illustration on 
the right is of DT-
V9L5.

u is displayed as 
“BATT.” on DT-F9L5.

DT-F9L5_EU.indb   27

DT-F9L5_EU.indb   27

2012/12/18   14:13:02

2012/12/18   14:13:02