Samsung SW-206 ユーザーズマニュアル
System Requirements
Installing the CD-R/RW Drive
Installing the Device Driver
4
5
Before you install the CD-R/RW drive, we strongly recommend that you make certain
that your set-up meets the system requirements listed below.
that your set-up meets the system requirements listed below.
Install the CD-R/RW drive in your computer horizontally, making sure that the Open/Close
button is on the right.
button is on the right.
1
Turn OFF your computer. Remember to verify the
configuration jumper on the rear of the CD-R/RW drive.
configuration jumper on the rear of the CD-R/RW drive.
To install the drive, proceed as follows.
2
Remove the cover of your PC(main unit of the computer).
3
Remove the blank cover panel of the 5.25 inch unit in
which the CD-R/RW drive is to be installed.
which the CD-R/RW drive is to be installed.
4
Connect the CD-R/RW drive to the IDE interface and
power cables located inside your computer.
☛ Connectors are keyed so it is impossible to put them in
power cables located inside your computer.
☛ Connectors are keyed so it is impossible to put them in
☛
an incorrect position. Do not force the connectors, if they
☛
do not seem to fit.
5
Install the CD-R/RW drive into the unit and secure it with
mounting screws (recommended standard M3x6).
☛ ◆ Depending on your PC model, you may need to attach
mounting screws (recommended standard M3x6).
☛ ◆ Depending on your PC model, you may need to attach
☛ ◆
guide rails to the drive, so that the drive is held firmly in place.
☛ ◆
On the ground that the guide rails are parts of the computer,
☛ ◆
if you don’t have these, please purchase separately.
☛
◆ If you use screws that are longer than the recommended
☛ ◆
standard, you may damage the drive.
6
Put the cover back on your PC.
Item
Description
Type of computer
Pentium 133MHz(or higher) with an IDE interface
(For 6X writing, 166MHz recommended)
16MB RAM(or higher) (Recommend 32MB)
528MB higher(Transfer Rate 800KB/sec higher, Access
Time 20msec Lower)
5.0(or higher)
TIP:For MS-DOS, The CD-R/RW drive can only Read a
disc without Premaster Software
(For 6X writing, 166MHz recommended)
16MB RAM(or higher) (Recommend 32MB)
528MB higher(Transfer Rate 800KB/sec higher, Access
Time 20msec Lower)
5.0(or higher)
TIP:For MS-DOS, The CD-R/RW drive can only Read a
disc without Premaster Software
RAM
Hard drive
Hard drive
MS-DOS
Microsoft
®
Windows 95
®
, 98
®
or Windows NT 4.0
®
TIP:For Windows NT
®
, we recommend Service Pack3.
Windows
You can install the device driver for DOS or for Windows.
TIP : You can use the CD-R/RW drive to only read a disc in DOS/Windows 3.1.
* Device Driver is located at [DDriver] folder of bundle [Recording S/W CD]
1
Turn on your computer and wait for it to boot.
7
Reboot your system.
Result:
Result:
◆
The computer restarts
◆
Both the device driver and MSCDEX are loaded.
6
When the
Setup Completed
screen is displayed, remove the installation
disk from the drive.
2
Insert the bundle CD into CD-R/RW driver.
4
Run the CDSETUP program:
5
To...
Then click...
Confirm the installation OK
Exit without installing CANCEL
Result:
Result:
If you answer Y(OK), the installation program automatically
◆
Creates a SAMSUNG directory on your hard disk
◆
Copies the required softwares (mscdex.exe and sscdrom.sys)
◆
Modifies the CONFIG.SYS and AUTOEXEC.BAT files
3
Windows 95/98 user
/NT 4.0
/NT 4.0
◆
When you are in Windows 95/98 or NT,
it is not necessary to install Device
Driver. Whereas, when you are in Dos
Mode of Windows 95/98 or NT,
then install as follows.
Driver. Whereas, when you are in Dos
Mode of Windows 95/98 or NT,
then install as follows.
◆
Click on
MY COMPUTER
icon.
◆
Click on the
CD-R/RW
icon.
Windows user
Double-click
CDSETUP.EXE
of
[DDRIVER] folder from the Windows File
Manager.
Manager.
English