Seagate ST240FP0021 ユーザーズマニュアル
S
EAGATE
600 P
RO
SSD P
RODUCT
M
ANUAL
, R
EV
. A
19
3.0
C
ONFIGURING AND MOUNTING THE DRIVE
This section contains the specifications and instructions for configuring and mounting the drive.
3.1
H
ANDLING AND STATIC
-
DISCHARGE PRECAUTIONS
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD)
hazards. Observe the following standard handling and static-discharge precautions:
hazards. Observe the following standard handling and static-discharge precautions:
Caution:
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a
computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.
• The drive is fragile—handle it with care.
• Always rest the drive on an antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty.
• Always rest the drive on an antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty.
Some factory-installed labels contain information needed to service the drive.
3.2
C
ONFIGURING THE DRIVE
Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave
relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on one
Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate
ports. Both drives behave as if they are Device 0 (master) devices.
relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on one
Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate
ports. Both drives behave as if they are Device 0 (master) devices.
Serial ATA drives are designed for easy installation. If you connect the drive and receive a “drive not detected” error, your
SATA equipped motherboard or host adapter may use a chipset that does not support SATA 6.0Gb speed autonegotiation.
You will need to install a SATA host adapter that supports autonegotiation.
SATA equipped motherboard or host adapter may use a chipset that does not support SATA 6.0Gb speed autonegotiation.
You will need to install a SATA host adapter that supports autonegotiation.
3.3
S
ERIAL
ATA
CABLES AND CONNECTORS
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable
size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 9 for connector pin definitions.
Either end of the SATA signal cable can be attached to the drive or host.
size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 9 for connector pin definitions.
Either end of the SATA signal cable can be attached to the drive or host.
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host
receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.
receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.
Figure 2.
Attaching SATA cabling
Each cable is keyed to ensure correct orientation. Seagate 600 Pro SSD drives support latching SATA connectors.
Power cable
Signal cable
Signal connector
Power connector