Seagate ST250LT007 - 9ZV14C ユーザーズマニュアル
M
OMENTUS
T
HIN
P
RODUCT
M
ANUAL
, G
EN
-2 R
EV
. G
22
5.0
S
ERIAL
ATA (SATA)
INTERFACE
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output
(PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to
provide reliable high-speed data transfers.
(PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to
provide reliable high-speed data transfers.
For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification.
5.1
H
OT
-P
LUG COMPATIBILITY
Momentus Thin drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA: High Speed
Serialized AT Attachment specification revision 2.0. This specification can be downloaded from http://www.serialata.org. This device
requires a COMRESET from the host after a hotplug event.
Serialized AT Attachment specification revision 2.0. This specification can be downloaded from http://www.serialata.org. This device
requires a COMRESET from the host after a hotplug event.
5.2
S
ERIAL
ATA
DEVICE PLUG CONNECTOR PIN DEFINITIONS
summarizes the signals on the Serial ATA interface and power connectors.
Table 7
Serial ATA connector pin definitions
Segment
Pin
Function
Definition
Signal
S1
Ground
2nd mate
S2
A+
Differential signal pair A from Phy
S3
A-
S4
Ground
2nd mate
S5
B-
Differential signal pair B from Phy
S6
B+
S7
Ground
2nd mate
Key and spacing separate signal and power segments
Power
P1
V
33
3.3V power
P2
V
33
3.3V power
P3
V
33
3.3V power, pre-charge, 2nd mate
P4
Ground
1st mate
P5
Ground
2nd mate
P6
Ground
2nd mate
P7
V
5
5V power, pre-charge, 2nd mate
P8
V
5
5V power
P9
V
5
5V power
P10
Ground
2nd mate
P11
Reserved
The pin corresponding to P11 in the backplane receptacle connector is also reserved
The corresponding pin to be mated with P11 in the power cable receptacle connector
shall always be grounded
The corresponding pin to be mated with P11 in the power cable receptacle connector
shall always be grounded
P12
Ground
1st mate.
P13
V
12
12V power, pre-charge, 2nd mate
P14
V
12
12V power
P15
V
12
12V power
N
OTE
1.
All pins are in a single row, with a 1.27 mm (0.050”) pitch.
2.
The comments on the mating sequence apply to the case of backplane blindmate connector only.
In this case, the mating sequences are:
In this case, the mating sequences are:
• the ground pins P4 and P12.
• the pre-charge power pins and the other ground pins.
• the signal pins and the rest of the power pins.
• the pre-charge power pins and the other ground pins.
• the signal pins and the rest of the power pins.
3.
There are three power pins for each voltage. One pin from each voltage is used for pre-charge
when installed in a blind-mate backplane configuration.
when installed in a blind-mate backplane configuration.
4.
All used voltage pins (V
x
) must be terminated.