Seagate MEDALIST 1276 (ST31276A) プリント

1. Turn off your computer and remove the cover.

2. Configure the master/slave jumpers as appropriate for your

system. If you have two hard discs, you must configure one as a
master and the other as a slave. Refer to the illustrations below for
details.

1. Connect the interface cable to the drive. Make sure that pin 1 on the

interface cable (colored stripe) is attached to pin 1 on the drive and
pin 1 on the host adapter.

2. Partially insert the drive into the drive bay. Select an unused power

connector from the power supply and connect it to the drive. If there
are no unused power connections on the power supply, you can
purchase a “Y” cable adapter from your dealer.

3. Secure the drive with four 6-32 x 0.25 screws. CAUTION: If you use

screws longer than 0.25 inch when mounting the drive, you may
damage the drive’s circuit board. The maximum insertion depth for
the bottom mounting holes is 0.25 inch; the maximum insertion
depth for the side holes is 0.125 inch.

This Seagate drive is shipped with free Disk Manager software. This
software partitions and formats the drive and allows older computers
to access the drive’s full capacity.

1. Insert a bootable DOS diskette in your A drive and restart your

computer. During the start-up process, enter your computer’s
System Setup program (sometimes called BIOS or CMOS setup).
This is usually done by pressing a special key, such as [DELETE],
[ESC], or [F1], during startup. See your computer manual for
system-specific instructions.

2. Within the System Setup program, make sure that a drive type is

listed for each ATA hard drive in your computer. Some newer
computers can automatically determine drive-type characteristics,
using the 

Auto drive-type setting. If your computer does not provide

this option, you must manually enter the number of cylinders, heads,
and sectors per track for your new drive, as shown in the table below.

ST3541A

16

1048

63

540 Mbytes

ST3636A

16

1241

63

635 Mbytes

ST31081A 16

2097

63

1082 Mbytes

ST31276A 16

2482

63

1275 Mbytes

ST31621A 16

3146

63

1623 Mbytes

*1 Mbyte = 1,000,000 bytes

3. Save the drive-type settings and exit the system setup program. You

will have to reboot your computer for the changes to take effect.

4. Insert your Disk Manager diskette. At the DOS prompt, type A:\DM.

Press [ENTER] to run Disk Manager

5. Follow the instructions on your computer screen. From the main

menu, select 

(E)asy Disk Installation. Then press [ENTER].

6. At this point, Disk Manager lists all the hard drives that it can

recognize. You should see your new Seagate drive and your old hard
drive (if any). If Disk Manager recognizes all your drives, select the
new drive you wish to install and press [ENTER]. Disk Manager will
format and partition your new drive.

If Disk Manager does not recognize a hard drive, exit Disk Manager
and turn off your computer. Check all cables, jumpers and BIOS
settings. Then run Disk Manager again.

7. Follow the instructions on the Disk Manager post-installation

screens. You're done!

NOTES:
1) If your computer does not require software support for large hard
drives, Disk Manager will optimize your system BIOS settings, then
quickly partition and format your new hard disc.
2) If Disk Manager has installed software to help your computer
access a large hard drive, you should see a blue Disk Manager banner
each time you boot your computer. In this case, if you need to boot
from a diskette instead of from your hard drive, see the Disk Manager
online manual for instructions.
3) To view the Disk Manager online manual, insert the Disk Manager
diskette and type A:\DM /H. Then press [ENTER]. You can also view
the online manual from within Disk Manager by selecting 

(V)iew/Print

Online Manual in the main menu.

1 3 5

2 4 6

Drive is slave

Drive is master in single-
or dual-drive system

Drive is master with
non-ATA-compatible slave

1

Enable Cable Select

2

2 

Consult your computer manual to determine 

   if your system supports cable select.

Master/slave
jumper settings

pin 1

4-pin power

connector

40-pin ATA

interface

connector

1 

Use this jumper setting 

only if the drive does

   not work with a single jumper on pins 5 and 6.

J4

Drive is slave

Drive is master or single drive (default)

Enable cable select*

1 3 5

9 11

2 4 6

1012 1416

131517

40-pin ATA

interface connector

4-pin power

connector

pin 1

*Consult your computer
manual to determine if your
system supports cable select