Seagate ST9300603SS ユーザーズマニュアル
Savvio 10K.3 SAS Product Manual, Rev. G
53
12.3.1
Inquiry data
Table 8 lists the Inquiry command data that the drive should return to the initiator per the format given in the
SAS Interface Manual.
SAS Interface Manual.
Table 8:
Savvio inquiry data
Bytes
Data (hex)
0-15
00
00
xx**
12
8B
00
PP
0A
53
45
41
47
41
54
45
20
Vendor ID
16-31
[53
54
39
33
30
30
36
30
33
53
53]
20
20
20
20
20
Product ID
32-47
R#
R#
R#
R#
S#
S#
S#
S#
S#
S#
S#
S#
00
00
00
00
48-63
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
64-79
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
80-95
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
96-111
00
43
6F
70
79
72
69
67
68
74
20
28
63
29
20
32*
*Copyright
112-127
30*
30*
36*
20
53
65
61
67
61
74
65
20
41
6C
6C
20
notice
128-143
72
69
67
68
74
73
20
72
65
73
65
72
76
65
64
20
*
Copyright year (changes with actual year).
**
SCSI Revision support. See the appropriate SPC release documentation for definitions.
PP
10 = Inquiry data for an Inquiry command received on Port A.
30 = Inquiry data for an Inquiry command received on Port B.
R#
Four ASCII digits representing the last four digits of the product firmware release number.
S#
Eight ASCII digits representing the eight digits of the product serial number.
[ ]
Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST9300603SS.
Refer to the values below for the values of bytes 16 through 26 of you particular model:
ST9300603SS
53 54 39 33 30 30 36 30 33 53 53
ST9300503SS
53 54 39 33 30 30 35 30 33 53 53
ST9300403SS
53 54 39 33 30 30 34 30 33 53 53
ST9146803SS
53 54 39 31 34 36 38 30 33 53 53
ST9146703SS
53 54 39 31 34 36 37 30 33 53 53
ST9146603SS
53 54 39 31 34 36 36 30 33 53 53
12.3.2
Mode Sense data
The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The
drive maintains four sets of mode parameters:
drive maintains four sets of mode parameters:
1.
Default values
Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
2.
Saved values
Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that
are allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
are allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
When power is applied to the drive, it takes saved values from the media and stores them as current val-
ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode
ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode