Seagate ST4000NM0043 ユーザーズマニュアル
58
Constellation ES Series SAS Product Manual, Rev. F
12.3.1
Inquiry data
Table 9 lists the Inquiry command data that the drive should return to the initiator per the format given in the
SAS Interface Manual.
SAS Interface Manual.
Table 9:
Constellation ES inquiry data
Bytes
Data (hex)
0-15
00
00
xx**
12
8B
00
30
02
53
45
41
47
41
54
45
20
Vendor ID
16-31
[53
54
33
32
30
30
30
34
34
34
53
53}
20
20
20
20
Product ID
32-47
R#
R#
R#
R#
S#
S#
S#
S#
S#
S#
S#
S#
00
00
00
00
48-63
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
64-79
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
80-95
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
96-111
00
43
6F
70
79
72
69
67
68
74
20
28
63
29
20
32*
*Copyright
112-127
30*
30*
39*
20
53
65
61
67
61
74
65
20
41
6C
6C
20
notice
128-143
72
69
67
68
74
73
20
72
65
73
65
72
76
65
64
20
*
Copyright year (changes with actual year).
**
SCSI Revision support. See the appropriate SPC release documentation for definitions.
PP
10 = Inquiry data for an Inquiry command received on Port A.
30 = Inquiry data for an Inquiry command received on Port B.
R#
Four ASCII digits representing the last four digits of the product firmware release number.
S#
Eight ASCII digits representing the eight digits of the product serial number.
[ ]
Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST32000444SS.
Refer to the values below for the values of bytes 16 through 26 of your particular model:
ST32000444SS
53
54
33
32
30
30
30
34
34
34
53
53
ST32000445SS
53
54
33
32
30
30
30
34
34
35
53
53
ST32000446SS
53
54
33
32
30
30
30
34
34
36
53
53
ST31000424SS
53
54
33
31
30
30
30
34
32
34
53
53
ST31000425SS
53
54
33
31
30
30
30
34
32
35
53
53
ST31000426SS
53
54
33
31
30
30
30
34
32
36
53
53
ST3500414SS
53
54
33
35
30
30
34
31
34
53
53
ST3500415SS
53
54
33
35
30
30
34
31
35
53
53
ST3500416SS
53
54
33
35
30
30
34
31
35
53
53
12.3.2
Mode Sense data
The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The
drive maintains four sets of mode parameters:
drive maintains four sets of mode parameters:
1.
Default values
Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
2.
Saved values