Seagate ST3500071FC ユーザーズマニュアル
NL35 Series FC Product Manual, Rev. D
55
9.3.1
Inquiry data
Table 24 lists the Inquiry command data that the drive should return to the initiator per the format given in the
Fibre Channel Interface Manual.
Fibre Channel Interface Manual.
Table 24:
NL35 Series inquiry data
*
Copyright year (changes with actual year).
**
02 = SCSI-2 implemented with some SCSI-3 features (default).
03 = The device complies to ANSI X3.301:199x
PP
50 = Inquiry data for an Inquiry command received on Port A.
70 = Inquiry data for an Inquiry command received on Port B.
R#
Four ASCII digits representing the last four digits of the product firmware release number.
S#
Eight ASCII digits representing the eight digits of the product serial number.
[ ]
Bytes 16 through 25 reflect drive model.
9.3.2
Mode Sense data
The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The
drive maintains four sets of mode parameters:
drive maintains four sets of mode parameters:
1.
Default values
Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
2.
Saved values
Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that
are allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
are allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
When power is applied to the drive, it takes saved values from the media and stores them as current val-
ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode
Select command before the drive achieves operating speed and is “ready.” An attempt to do so results in a
“Check Condition” status.
ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode
Select command before the drive achieves operating speed and is “ready.” An attempt to do so results in a
“Check Condition” status.
On drives requiring unique saved values, the required unique saved values are stored into the saved val-
ues storage location on the media prior to shipping the drive. Some drives may have unique firmware with
unique default values also.
ues storage location on the media prior to shipping the drive. Some drives may have unique firmware with
unique default values also.
Bytes
Data (hex)
0-15
00
00
**
12
8B
00
PP
0A
53
45
41
47
41
54
45
20
Vendor ID
16-31
[53
54
33
35
30
30
30
37
31
46
43]
20
20
20
20
20
Product ID
32-47
R#
R#
R#
R#
S#
S#
S#
S#
S#
S#
S#
S#
00
00
00
00
48-63
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
64-79
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
80-95
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
96-111
00
43
6F
70
79
72
69
67
68
74
20
28
63
29
20
32*
*Copyright
112-127
30*
30*
36*
20
53
65
61
67
61
74
65
20
41
6C
6C
20
notice
128-143
72
69
67
68
74
73
20
72
65
73
65
72
76
65
64
20