Seagate ST36451A ユーザーズマニュアル
p y
p
p
by the BIOS.
!
Caution. If you change the drive-type values in the
system setup program, you must partition and
format the drive again.
system setup program, you must partition and
format the drive again.
This erases data on the drive.
•
If you have partitioned the drive into individual logical drives, you may
need to make the partitions smaller to access the full drive capacity.
need to make the partitions smaller to access the full drive capacity.
•
If your computer supports LBA mode, you may need to enable LBA
mode in the system setup program to access the full capacity of the drive.
Refer to your computer’s reference guide to find out how to enable LBA.
mode in the system setup program to access the full capacity of the drive.
Refer to your computer’s reference guide to find out how to enable LBA.
•
Your computer may not support drives that have more than 4,096
cylinders. Follow the instructions for
cylinders. Follow the instructions for
After you install your new drive, your
computer will not boot, and no error message shows on the screen.
The DOS messages “Disk Boot Failure,” “Non-System Disk” or
“No ROM Basic – SYSTEM HALTED” appear.
“No ROM Basic – SYSTEM HALTED” appear.
•
Reinstall the DOS system files using the DOS SYS utility.
•
Check all cables.
•
Use FDISK to verify that the primary partition is active.
•
Check for viruses.
The system error message, “HDD controller failure” appears.
•
Confirm the jumper settings on the drive.
•
Verify the drive-type settings in the system setup program.
32-bit Disk Access under Windows 3.1.
The 32-bit disk access feature in Windows 3.1 does not work with drives
that have capacities greater than 528 Mbytes. If you want to use 32-bit disk
access under Windows 3.1, install the Seagate replacement 32-bit access
driver, SEG32BIT.386, located on your DiscWizard diskette.
that have capacities greater than 528 Mbytes. If you want to use 32-bit disk
access under Windows 3.1, install the Seagate replacement 32-bit access
driver, SEG32BIT.386, located on your DiscWizard diskette.
Note. If you install Windows 3.1 on a high-capacity
hard drive, the first time you start Windows you may
see a message suggesting that you disable 32-bit
disk access. Choose to disable 32-bit disk access to
open Windows.
hard drive, the first time you start Windows you may
see a message suggesting that you disable 32-bit
disk access. Choose to disable 32-bit disk access to
open Windows.
Use the following procedure to install the Seagate 32-bit disk access
replacement driver (from within Windows).
replacement driver (from within Windows).
1 Insert your DiscWizard diskette into Drive A.
2
Open the Windows Program Manager menu and select File.
3
Select Run.
4
In the command line box, type a:\stsetup and then press
ENTER
.
5
Read the license agreement that appears on the screen. If you agree
to the terms, select
to the terms, select
Accept Agreement to continue.
6
The next screen lists the features that the SEG32BIT.386 driver
supports. If your computer supports these features, they will be active in
32-bit disk access mode for all drives that support them. Select
supports. If your computer supports these features, they will be active in
32-bit disk access mode for all drives that support them. Select
Install
Driver to continue.
7 Enable the 32-bit disk access option in the Windows control panel as follows:
a) Open the Windows Control Panel.
b) Select
b) Select
386 Enhanced.
c) Select
Virtual Memory.
d) Select
Change>>.
e) Select
Use 32-Bit Disk Access (an X in the box enables the feature).
f) Save the change.
Foam
Antistatic bag
Drive
Foam
Hong Kong 852-2368 7173
USA
408-944-9120
Direct-Support Services
Seagate Technical Support
For one-on-one help, you can talk to a technical support specialist during
local business hours. Before calling, note your system configuration and
drive model number (ST
local business hours. Before calling, note your system configuration and
drive model number (ST
xxxxxx).
Location
Phone number
Location
Phone number
Australia
61-2-9725-3366
Korea
82-2-556-8241
England
44-1628-894083
Singapore
65-488-7584
France
33 1-41 86 10 86
Taiwan
886-2-514-2237
Germany
49-89-140-9332
USA
1-800-SEAGATE or
Hong Kong 852-2368 9918
USA
408-456-4496
SeaTDD™
408-944-9121
Using a telecommunications device for the deaf (TDD), you can send
questions or comments 24 hours daily and exchange messages with a
technical support specialist between 6:00
questions or comments 24 hours daily and exchange messages with a
technical support specialist between 6:00
A
.
M
. to 11:15
A
.
M
. and
12:30
P
.
M
. to 5:00
P
.
M
. (Pacific time) Monday through Friday.
Keep your original box and packing materials
for storing or shipping your drive. The box has
a
for storing or shipping your drive. The box has
a
Seagate Approved Package label. Shipping a
drive in an unapproved container voids the
warranty. Call your authorized Seagate
distributor to purchase additional boxes. The
figure to the right shows how a drive fits in an
approved single-pack box, including the
packing materials.
warranty. Call your authorized Seagate
distributor to purchase additional boxes. The
figure to the right shows how a drive fits in an
approved single-pack box, including the
packing materials.
Warranty. See your authorized Seagate
distributor or dealer. Preinstalled or bundled
software is provided “as is.” There are no
warranties of merchantablity or fitness for a
particular purpose. All such warranties are
expressly and specifically disclaimed.
distributor or dealer. Preinstalled or bundled
software is provided “as is.” There are no
warranties of merchantablity or fitness for a
particular purpose. All such warranties are
expressly and specifically disclaimed.
Maintenance and repair. Seagate drives do
not require maintenance. The head/disc
assembly is sealed; a broken seal voids the
warranty. Seagate customer-service centers
are the only facilities authorized to repair
Seagate drives.
not require maintenance. The head/disc
assembly is sealed; a broken seal voids the
warranty. Seagate customer-service centers
are the only facilities authorized to repair
Seagate drives.
Electromagnetic Compliance for the European Union. This model complies with the
European Union requirements of the Electromagnetic Compatibility Directive 89/336/
EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and Directive
93/68/EEC of 22 July 1993.
European Union requirements of the Electromagnetic Compatibility Directive 89/336/
EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and Directive
93/68/EEC of 22 July 1993.
Compliance of this drive, as a system component, was confirmed with a test system. We
cannot guarantee that your system will comply. The drive is not meant for external use
(without properly designed enclosure, shielded I/O cable, etc.).
cannot guarantee that your system will comply. The drive is not meant for external use
(without properly designed enclosure, shielded I/O cable, etc.).
Sicherheitsanleitung 1. Das Gerrät ist ein Einbaugerät, das für eine maximale
Umgebungstemperatur von 55°C vorgesehen ist. 2. Zur Befestigung des Laufwerks
werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale
Länge der Schrauben im Chassis nicht mehr als 3,3 mm und bei Befestigung an der
Unterseite nicht mehr als 5,08 mm betragen. 3. Als Versorgungsspannugen werden
benötigt: +5V ± 5% 0,6A; +12V ±% 0,8A (1,9A fur ca. 30 Sek. fur ± 10%) 4. Die
Versorgungsspannung muss SELV entsprechen. 5. Alle Arbeiten auf dem Festplatte
dürfen nur von Ausgebildetem Servicepersonal durchgeführt werden. Bitte entfernen Sie
nicht die Aufschriftenschilder des Laufwerkes. 6. Der Einbau des Laufwerkes muss den
Anforderungen gemäss DIN IEC 950 VDE 0805/05.90 entsprechen.
Umgebungstemperatur von 55°C vorgesehen ist. 2. Zur Befestigung des Laufwerks
werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale
Länge der Schrauben im Chassis nicht mehr als 3,3 mm und bei Befestigung an der
Unterseite nicht mehr als 5,08 mm betragen. 3. Als Versorgungsspannugen werden
benötigt: +5V ± 5% 0,6A; +12V ±% 0,8A (1,9A fur ca. 30 Sek. fur ± 10%) 4. Die
Versorgungsspannung muss SELV entsprechen. 5. Alle Arbeiten auf dem Festplatte
dürfen nur von Ausgebildetem Servicepersonal durchgeführt werden. Bitte entfernen Sie
nicht die Aufschriftenschilder des Laufwerkes. 6. Der Einbau des Laufwerkes muss den
Anforderungen gemäss DIN IEC 950 VDE 0805/05.90 entsprechen.
Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate
Technology, Inc. SeaFAX, SeaFONE, SeaBOARD, SeaNET, SeaTDD, Medalist, the Medalist
logo and DiscWizard are either trademarks or registered trademarks of Seagate
Technology, Inc. or one of its subsidiaries. All other trademarks or registered trademarks
are the property of their respective owners.
Technology, Inc. SeaFAX, SeaFONE, SeaBOARD, SeaNET, SeaTDD, Medalist, the Medalist
logo and DiscWizard are either trademarks or registered trademarks of Seagate
Technology, Inc. or one of its subsidiaries. All other trademarks or registered trademarks
are the property of their respective owners.
Seagate reserves the right to change, without notice, product offerings or
specifications. No part of this publication may be reproduced in any form without
written permission from Seagate Technology, Inc.
specifications. No part of this publication may be reproduced in any form without
written permission from Seagate Technology, Inc.
© 1997 Seagate Technology, Inc.
920 Disc Drive, Scotts Valley, CA 95066, USA
Publication Number: 32656-001, Rev. B, July 1997, Printed in USA
920 Disc Drive, Scotts Valley, CA 95066, USA
Publication Number: 32656-001, Rev. B, July 1997, Printed in USA