Seagate ST330630A プリント

DiscWizard



 is Seagate’s exclusive Windows program that is included with

your drive for easy drive installation. You can use this software if you
already have a bootable hard drive in your computer and you are running
Windows 98 or Windows 95.

Run DiscWizard 

before 

installing your drive for customized step-by-step

instructions for your system.

To run DiscWizard:

• 

Select Run from the Windows Start menu and type 

:\setup, where

 x

 is

the drive letter of your diskette or CD-ROM.

If you cannot run DiscWizard, follow the instructions on this installation
sheet to install and configure your drive.

•

 Phillips screwdriver and four 6-32 UNC drive mounting screws

•

 A standard 40-pin ATA interface cable, 

or

 an 80-conductor cable to run

Ultra ATA 66 (max length: 18 inches)

•

 An unused drive power cable for your new drive

The drive can support transfer rates up to 66 Mbytes per second
(UDMA 4) in Ultra ATA/66 mode. For your drive to run in this mode, you
need the following:

•

 A computer that supports UDMA modes 3 and 4

•

 A 40-pin 80-conductor cable (available from your dealer)

•

 A software utility to confirm and activate Ultra ATA/66. Seagate

®

 provides

a utility called UATA66.exe that is included on your CD, or you can
download it from our Web site at www.seagate.com.

•

 The Windows 98 operating system

Disc drives are extremely fragile.

 Do not 

drop or jar the drive.

Keep the drive in the protective SeaShell



 container until you are

ready to install it. This will minimize handling damage.

The drive has a protective cover called SeaShield

®

. Do not remove

this permanent cover—it protects the drive from electrostatic
discharge (ESD) and minor impact damage.

Protect your drive from static discharge by wearing a grounded wrist
strap throughout the installation process.

Always handle the drive by the edges or frame.

Do not apply pressure or attach labels to the circuit board or the
top of the drive.

Refer to the jumper settings below to configure the drive for your system.

•

 Master or single-drive: The drive is shipped configured for a master

or a single-drive with a jumper set on pins 7 and 8.

• 

Drive is slave: To configure the drive as a slave, or second drive on

the cable, remove all the jumpers.

• 

Master with non-ATA compatible slave: Use this setting if the slave

drive is not recognized. Configure the master drive with a jumper set on
pins 5 and 6 and pins 7 and 8 to enable this option.

• 

Cable-select option:  Computers that use cable-select determine the

master and slave drives by selecting or deselecting pin 28, CSEL, on
the interface bus. To enable cable select, set a jumper on pins 5 and 6.

1. Attach one end of the drive interface cable to the interface connector

on your computer’s motherboard

 

(see your computer manual for

connector locations).

 Caution.  Align pin 1 on the motherboard connector with pin 1 on

your drive connector. Pin 1 is marked by a stripe on one side of the cable.

2. Attach the interface connector and the power connector to the drive.

Note. You can mount the drive in any orientation. Usually it is mounted

      with the circuit board down.

3. Secure the drive in the computer using four 6-32 UNC mounting

screws in either the side-mounting or bottom-mounting holes. Insert
the screws no more than 0.20 inch (5.08 mm) into the bottom-mounting
holes and no more than 0.14 inch (3.55 mm) into the side-mounting holes.

 Caution. Do not overtighten the screws or use metric screws. This

may damage the drive.

For your computer to recognize your new drive, configure your
computer’s BIOS as follows:

1. Run the system setup program.

2. Enable LBA mode and UDMA mode, if available.

3. Select the auto-detect option. If this is not available, select “User-

defined drive type” and enter the CHS (cylinder, head, sectors)
parameters for your drive from the table listed below. The CHS
addressing supports capacities up to 8.4 Gbytes only. To access the
full capacity of the drive, use LBA mode.

4. Save and exit the system setup program.

ST330630A

16,383

16

63

59,777,640

ST320420A

16,383

16

63

39,851,760

ST315320A

16,383

16

63

29,888,820

ST310210A

16,383

16

63

19,925,880

*One sector equals 512 bytes.

Pin 1

Interface
connector

Power
connector

Computer

Motherboard

Pin 1

Note. If you are using a 40-pin 80-conductor

cable, attach the 

blue connector to the 

motherboard, the 

black connector to the

master drive, and the 

grey connector

to the slave.

Circuit Board

2

6

8

4

1

7 5 3

Drive is slave 

Alternate capacity

 

Master with a non-ATA-
compatible slave

Master or single-drive