Seagate ST9146853SS ユーザーズマニュアル
52
Savvio 15K.3 SAS Product Manual, Rev. A
12.3.1
Inquiry data
Table 8 lists the Inquiry command data that the drive should return to the initiator per the format given in the
SAS Interface Manual.
SAS Interface Manual.
Table 8:
Savvio inquiry data
*
Copyright year (changes with actual year).
**
SCSI Revision support. See the appropriate SPC release documentation for definitions.
PP
10 = Inquiry data for an Inquiry command received on Port A.
30 = Inquiry data for an Inquiry command received on Port B.
R#
Four ASCII digits representing the last four digits of the product firmware release number.
S#
Eight ASCII digits representing the eight digits of the product serial number.
[ ]
Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST9300653SS.
Refer to the values below for the values of bytes 16 through 26 of your particular model:
ST9300553SS
53
54
39
33
30
30
35
35
33
53
53
ST9300453SS
53
54
39
33
30
30
34
35
33
53
53
ST9146853SS
53
54
39
31
34
36
38
35
33
53
53
ST9146753SS
53
54
39
31
34
36
37
35
33
53
53
ST9146653SS
53
54
39
31
34
36
36
35
33
53
53
12.3.2
Mode Sense data
The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The
drive maintains four sets of mode parameters:
drive maintains four sets of mode parameters:
1.
Default values
Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
2.
Saved values
Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that
are allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
are allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
When power is applied to the drive, it takes saved values from the media and stores them as current val-
ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode
ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode
Bytes
Data (hex)
0-15
00
00
03**
12
8B
00
PP
0A
53
45
41
47
41
54
45
20
Vendor ID
16-31
[53
54
39
33
30
30
36
35
33
53
53]
20
20
20
20
20
Product ID
32-47
R#
R#
R#
R#
S#
S#
S#
S#
S#
S#
S#
S#
00
00
00
00
48-63
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
64-79
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
80-95
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
96-111
00
43
6F
70
79
72
69
67
68
74
20
28
63
29
20
32*
*Copyright
112-127
30*
31*
30*
20
53
65
61
67
61
74
65
20
41
6C
6C
20
notice
128-143
72
69
67
68
74
73
20
72
65
73
65
72
76
65
64
20