Seagate ST3146707FC/FCV プリント

The drive has been low level formatted at the factory. You do not need to
perform another low level format on this drive unless you decide to perform
certain diagnostics through the host adapter. If you do decide to perform a
low level format, do not abort the format as this is likely to make the drive
inoperable. A low level format, with verify turned on, will typically take two
hours.

Protect against power failure or other power interruptions during the format.

a.

Turn on DC power to the host system.

b.

Boot the system from a system floppy, CD, or from a previously
installed hard disc drive if there is one.

c.

Format the drive. 

Caution. Formatting a drive erases all user data. Be sure that you under-

stand this principle before formatting any hard disc drive. It is not
necessary to format a drive that previously has been used to
store data, unless your intention is to erase all user data.

Seagate

®

 is not responsible for lost user data.

Cheetah

®

 10K.7 disc drives are designed to operate with a variety of oper-

ating systems. Please refer to your system or Fibre Channel host adapter
(controller) manual for information about formatting and setting up the drive
for use with your particular operating system.

This drive features hot plugging capabilities which allow you to insert and
remove the drive without powering down the host system. Any time a drive
is inserted or removed from a Fibre Channel loop, a short loop interruption
occurs and the loop resynchronizes automatically to accommodate the
added (or removed) drive. 

The drive’s motor will start spinning the discs based on the status of two sig-
nals set by the host adapter. These two signals are called Start_1 and
Start_2. There are four options as described below.

1 ........... Low ....... Low ........ Motor spins up at DC power on.

2 ........... High ...... Low ........ Motor spins up when the host adapter sends

the SCSI Start command.

3 ........... Low ....... High........ Motor spins up after a delay of 12 seconds

times the physical address of the drive.

4 ........... High ...... High........ The drive will not spin up.

Most systems that host only a couple of drives use option 1 to enable all of
the drives to start up immediately when power is applied to the drives. Sys-
tems hosting larger numbers of drives may be configured to start drives at
various times to avoid overloading the capabilities of the host system’s
power supply.

If you want to change the startup option for the drive, please refer to the
documentation provided with your Fibre Channel host adapter or host sys-
tem.

• Drive does not spin up. Remove and then reinsert the drive into the

drive bay on the host-supplied carrier or tray. Make sure the drive makes
firm contact with the host’s FC backpanel connector. Also, check the
drive startup options for the Start_1 and Start_2 signals controlled from
your host adapter. See “Drive Startup Options” above for the four possi-
ble startup options.

• Computer does not seem to recognize the drive. Verify that the drive

is enabled by the FC host adapter setup utility.

For online information about Seagate products, visit www.seagate.com or
e-mail your disc questions to DiscSupport@Seagate.com.

If you need help installing your drive, consult your dealer first. If you need
additional help, call a Seagate technical support specialist. Before calling,
note your system configuration and drive model number.

Africa

+1-405-324-4714

Netherlands

00 800-47324283

Australia

1800-14-7201

New Zealand

0800-443988

Austria

0 800-20 12 90

Norway

00 800-47324283

Belgium

00 800-47324283

Poland

00 800-311 12 38

China*

800-810-9668

Spain

00 800-47324283

Denmark

00 800-47324283

Sweden

00 800-47324283

France

00 800-47324283

Switzerland

00 800-47324283

Germany

00 800-47324283

Singapore

800-1101-150

Hong Kong

800-90-0474

Taiwan*

00-800-0830-1730

Hong Kong† 001-800-0830-1730

Thailand

001-800-11-0032165

India

1-600-33-1104

Turkey

00 800-31 92 91 40

Indonesia

001-803-1-003-2165

United Kingdom 00 800-47324283

Ireland

00 800-47324283

USA/Canada/

1-800 SEAGATE or

Italy

00 800-47324283

Latin America

+1-405-324-4700

Japan

0034 800 400 554

Other European

Malaysia

1-800-80-2335

countries

+1-405-324-4714

Middle East +1-405-324-4714

*Mandarin
†Cantonese

Warranty. Contact your place of purchase or our web site (above). 
Return Merchandise Authorization (RMA).

Before returning the drive, verify that it

is defective. Seagate Worldwide customer service centers are the only facilities autho-
rized to service Seagate drives. Contact nearest center for return procedures and trade
regulations.

Back up the data before shipping. Seagate assumes no responsibility for

data lost during shipping or service. Shipping drive in an unapproved container voids
the warranty. Pack the drive with original box and packing materials. Use no other
materials. This prevents electrical and physical damage in transit.