Seagate ST336705LW/LC ユーザーズマニュアル
50
Cheetah 36XL Product Manual, Rev. E
Current values are volatile values currently being used by the drive to control its operation. A Mode Select com-
mand can be used to change these values (only those that are changeable). Originally, they are installed from
saved or default values after a power on reset, hard reset, or Bus Device Reset message.
mand can be used to change these values (only those that are changeable). Originally, they are installed from
saved or default values after a power on reset, hard reset, or Bus Device Reset message.
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of the current values and
saved values can be changed by a Mode Select command. A “one” allows a change to a corresponding bit; a
“zero” allows no change. For example, in Table 7 refer to Mode page 01, in the row entitled “CHG”. These are
hex numbers representing the changeable values for mode page 01. Note that bytes 04, 05, 06, and 07 are not
changeable, because those fields are all zeros. If some changeable code had a hex value EF, that equates to
the binary pattern 1110 1111. If there is a zero in any bit position in the field, it means that bit is not change-
able. Bits 7, 6, 5, 3, 2, 1, and 0 are changeable, because those bits are all ones. Bit 4 is not changeable.
saved values can be changed by a Mode Select command. A “one” allows a change to a corresponding bit; a
“zero” allows no change. For example, in Table 7 refer to Mode page 01, in the row entitled “CHG”. These are
hex numbers representing the changeable values for mode page 01. Note that bytes 04, 05, 06, and 07 are not
changeable, because those fields are all zeros. If some changeable code had a hex value EF, that equates to
the binary pattern 1110 1111. If there is a zero in any bit position in the field, it means that bit is not change-
able. Bits 7, 6, 5, 3, 2, 1, and 0 are changeable, because those bits are all ones. Bit 4 is not changeable.
Though the drive always reports non-zero values in bytes 00 and 01, those particular bytes are never change-
able.
able.
The Changeable values list can only be changed by downloading new firmware into the flash EPROM.
On standard OEM drives the Saved values are taken from the default values list and stored into the saved val-
ues storage location on the media prior to shipping.
ues storage location on the media prior to shipping.
When a drive is powered up, it takes saved values from the media and stores them to the current values stor-
age in volatile memory. It is not possible to change the current values (or the saved values) with a Mode Select
command before the drive is up to speed and is “ready.” An attempt to do so results in a “Check Condition sta-
tus being returned.
age in volatile memory. It is not possible to change the current values (or the saved values) with a Mode Select
command before the drive is up to speed and is “ready.” An attempt to do so results in a “Check Condition sta-
tus being returned.
Note.
Because there may be several different versions of drive control firmware in the total population of
drives in the field, the Mode Sense values given in the following tables may not exactly match those of
some drives.
drives in the field, the Mode Sense values given in the following tables may not exactly match those of
some drives.
The following tables list the values of the data bytes returned by the drive in response to the Mode Sense com-
mand pages for SCSI Ultra160 implementation (see the
mand pages for SCSI Ultra160 implementation (see the
SCSI Interface Product Manual, part number
75789509).
Definitions:
SAV = Saved value.
DEF = Default value. Standard drives are shipped configured this way.
CHG = Changeable bits; indicates if current and saved values are changeable.
DEF = Default value. Standard drives are shipped configured this way.
CHG = Changeable bits; indicates if current and saved values are changeable.
Note.
Saved values for OEM drives are normally the same as the default values.