Seagate ST3400832A プリント

ST3400832A

400.0

781,422,768

8 Mbytes

ST3300831A

300.0

586,072,368

8 Mbytes

ST3250823A

250.0

488,397,168

8 Mbytes

ST3200826A

200.0

390,721,968

8 Mbytes

*One sector equals 512 bytes.

Installing a single drive
If you are installing a single drive, we recommend using DiscWizard to
automatically partition and format your drive. DiscWizard software is avail-
able at www.seagate.com and is free. During the download, the Diskette
Creator creates a portable bootable diskette. To run DiscWizard:

1.

Insert your bootable DiscWizard diskette and follow the instructions.
DiscWizard will guide you through the installation process.

2.

Boot your computer from the Windows operating system CD-ROM or
from your system startup diskette with the Windows CD loaded. At the
prompt, type setup. Follow the instructions provided on your screen.

Installing a slave drive
If you are installing a second drive, or slave, to your system, use the Dis-
cWizard software available at www.seagate.com.
If you do not want to install your drive using either DiscWizard or Disk Man-
ager, see “Standard Microsoft Installation” below to partition and format
your drive.

Caution. Partitioning or formatting a drive erases all data on the drive.

Seagate assumes no liability if you erase your data.

1.

Insert a bootable Windows startup diskette and restart your computer.
This is provided with your Microsoft Windows operating system soft-
ware.

2.

Run fdisk and create a primary DOS partition.

3.

Mark the partition as active to make the partition bootable.

Caution. Use the correct drive letters to prevent formatting a drive that

already contains data.

1.

At the A: prompt, type format x: (where x is the letter of your first new
partition) and then press the Enter key. Repeat the format process for
all new partitions.

2.

Proceed to “Loading the operating system” below.

Note. The operating system needs to be installed on the master drive

only. It is not required when adding a second drive.

1.

Boot your computer from your Windows operating system CD-ROM or
from your system startup diskette with the Windows CD loaded in the
CD drive.

2.

At the prompt, type setup and continue with the Windows setup as
instructed on your screen.

If your drive is not working properly, these troubleshooting tips may help
solve the problem.

1.

Does the drive spin up? A spinning drive produces a faint whine and
clicking noise that begins when power is applied. If your drive does not
spin, check that the power connector and interface cable are securely
attached and the jumpers are installed correctly.

2.

Does the computer recognize the drive? Verify that the drive is
enabled in the system CMOS or setup program. If not, select the auto-
detect option and enable it. If your drive has a problem, it may not be
recognized by the system.

3.

Does FDISK detect the drive? Run the FDISK program located on
your Windows startup diskette. Type fdisk/status to verify that your
hard drive is present and recognized by the system.

4.

Does Scandisk find the drive defect-free? Scandisk is a utility
located on your Windows startup diskette that scans the drive for
defects. If defects are detected, this may be an indication of a problem.

5.

Why won’t the drive format to full capacity? Verify that your BIOS
has autodetect and LBA mode enabled. Otherwise, you may need to
use Disk Manager to achieve the full capacity of your drive. Download
the latest version from www.seagate.com or find it on your CD.

6.

Why does my computer hang on startup? Verify that your system is
ATA/100 compatible with the UDMA mode setting. Some legacy BIOS
cause hangs on startup or other problems if it is not ATA/100 compati-
ble. For more information, see the earlier section on the Ultra ATA/100
requirements. In addition, some legacy BIOS may cause a hang due to
the large drive capacity. Consider using the alternate capacity jumper if
it is available on your drive model. 
Use the alternate capacity jumper if your computer does not support
higher capacity drives. The jumper will limit large capacity drives to 32
Gbytes.

Note. If these tips do not answer your question or solve the problem, con-

tact your dealer or visit http://seatools.seagate.com to download
SeaTools disc diagnostics software and more troubleshooting
advice.

For online information about Seagate products, visit www.seagate.com or
e-mail your disc questions to DiscSupport@Seagate.com.

If you need help installing your drive, consult your dealer first. If you need
additional help, call a Seagate technical support specialist. Before calling,
note your system configuration and drive model number.

Africa

+1-405-324-4714

Netherlands

00 800-47324283

Australia

1800-14-7201

New Zealand

0800-443988

Austria

0 800-20 12 90

Norway

00 800-47324283

Belgium

00 800-47324283

Poland

00 800-311 12 38

China*

800-810-9668

Spain

00 800-47324283

Denmark

00 800-47324283

Sweden

00 800-47324283

France

00 800-47324283

Switzerland

00 800-47324283

Germany

00 800-47324283

Singapore

800-1101-150

Hong Kong

800-90-0474

Taiwan*

00-800-0830-1730

Hong Kong*

001-800-0830-1730

Thailand

001-800-11-

0032165
India

1-600-33-1104

Turkey

00 800-31 92 91 40

Indonesia

001-803-1-003-2165

United Kingdom

00 800-47324283

Ireland

00 800-47324283

USA/Canada/

1-800 SEAGATE or

Italy

00 800-47324283

Latin America

+1-405-324-4700

Malaysia

1-800-80-2335

Other European

Middle East

+1-405-324-4714

countries

+1-405-324-4714

*Chinese

Warranty. To determine the warranty status of your Seagate disc drive, contact your
place of purchase or visit our web site at www.seagate.com for more information. 
Return Merchandise Authorization (RMA).

Run SeaTools to diagnose your drive

before requesting a return authorization. In addition, please verify that your drive is
defective by following the troubleshooting checklist in this guide. Seagate offers com-
prehensive customer support for all Seagate drives worldwide. Seagate customer
service centers are the only facilities authorized to service Seagate drives. Drive
return procedures vary depending on geographical location and are subject to current
international trade regulations.

Shipping the drive
Caution. Back up the data before shipping. Seagate assumes no responsibility for

data lost during shipping or service.

Shipping drive in an unapproved container voids the warranty. Pack the drive with
original box and packing materials. Use no other materials. This prevents electrical
and physical damage in transit.

Electromagnetic compliance for the European Union. This model complies with
the European Union requirements of the Electromagnetic Compatibility Directive 89/
336/EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and
Directive 93/68/EEC of 22 July 1993. Compliance of this drive, as a system compo-
nent, was confirmed with a test system. We cannot guarantee that your system will
comply. The drive is not meant for external use (without properly designed enclosure,
shielded I/O cable, etc.).

Sicherheitsanleitung  1. Das Gerrät ist ein Einbaugerät, das für eine maximale
Umgebungstempeatur von 60°C vorgesehen ist. 2. Zur Befestigung des Lufwerks
werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maxi-
male Länge der Schrauben im Chassis nicht merh als 3,3 mm und bei Befestigung an
der Unterseite nicht mehr als 5,08 mm betragen. 3. Als Versorgungsspannugen wer-
den benötigt: +5V +/- 5% 1,2A; +12V +/- 5% 2,0A 4. Die Versorgungsspannung muss
SELV entsprechen. 5. Alle Arbeiten auf dem Festplattte dürfen nur von Ausgebiletem
Serciepersonal durchgeführt werden. Bitte entfernen Sie nicht die Aufschriftens-
childer des Laufwerkes. 6. Der Einbau des Laufwerkes muss den Anforderungen
gemäss DIN IEC 950 VDE 0805/05.90 entspreche.