Addonics Technologies AEIDDSAUWP プリント
ADDONICS TECHNOLOGIES
Model: AEIDDSAU, AEIDDSAUWP (read only mode)
The internal SATA / USB DigiDrive supports Type I, II
CF Cards, CF Micro drive, SD, SDHC, miniSD (with
adapter), Trans flash, SD HS (Secure Digital High
Speed), MMC Cards (4-bit and 8-bit modes), RS-
MMC, MMC-Micro, MMC Plus, Smart Media, xD
picture card- both H and M types, Memory stick,
Memory stick PRO, MS Extreme III Type media, MS
PRO, HS (4-bit mode).
CF Cards, CF Micro drive, SD, SDHC, miniSD (with
adapter), Trans flash, SD HS (Secure Digital High
Speed), MMC Cards (4-bit and 8-bit modes), RS-
MMC, MMC-Micro, MMC Plus, Smart Media, xD
picture card- both H and M types, Memory stick,
Memory stick PRO, MS Extreme III Type media, MS
PRO, HS (4-bit mode).
Mode Jumper (JP4):
Note: Only applies on SATA connection
Note: Only applies on SATA connection
I.
Setting up the device in SATA mode
a. Connect a 4-pin floppy power cable from PC to the
internal SATA / USB DigiDrive.
b. Attach SATA cable from internal SATA / USB
DigiDrive to the PC SATA port.
The tables show drive icon and media detection
behavior basing on the mode switch setting and the
type of SATA port the internal SATA / USB DigiDrive is
connected to.
Open mode – force flash media to become Fixed disk
type
Drive icon
Media Detection
Hot Swap
SATA port
SATA port
Icon appears only
when flash media is
inside
when flash media is
inside
Flash media is
automatically
refresh and
detected when
added or removed
automatically
refresh and
detected when
added or removed
Non hot swap
SATA port
SATA port
Icon appears only
when flash media is
inside
when flash media is
inside
Flash media
detection requires
manual refresh in
Device Manager
detection requires
manual refresh in
Device Manager
Close mode – force flash media to become
Removable disk type
Drive icon
Media Detection
Hot Swap
SATA port
SATA port
NOT RECOMMENDED
Non hot swap
SATA port
SATA port
Icon always there
with or without flash
media inside the
DigiDrive
with or without flash
media inside the
DigiDrive
Flash media
automatically
detected when
added or remove
automatically
detected when
added or remove
II.
Setting up the device in USB Mode
a. Connect a 4-pin floppy power cable to the internal
SATA / USB DigiDrive.
b. Attach USB 5-pin header from internal SATA /
USB DigiDrive to USB header on PC.
c. The drive icon appears only when flash media is
inside the internal SATA / USB
DigiDrive.The drive
icon will disappear and reappear during media
change.
change.
Note for AEIDDSAUWP: If an unformatted flash media
is use, no drive icon will show up in My Computer.
Media Priority
When more than one media is inside the internal
SATA / USB DigiDrive during bootup, the media that
gets detected first is according to the priority shown
below
When more than one media is inside the internal
SATA / USB DigiDrive during bootup, the media that
gets detected first is according to the priority shown
below
1. Compact
Flash
2.
Smart Media / xD Picture card
3.
MMC / SD
4.
Memory Stick
TECHNICAL SUPPORT
Email:
http://www.addonics.com/sales/query/
Internet:
http://www.addonics.com
Technical Support (8:30 am to 6:00 pm PST)
Phone: 408 453-6212
Email: http://www.addonics.com/support/query/
USB 5-pin
header
header
Mode jumper JP4
(close or open)
(close or open)
SATA port
4-pin floppy
power connector
power connector
Pin 1