JVC AA-T100BT プリント

ページ / 2
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
MANUAL DE INSTRUCCIONES
BLUETOOTH TRANSMITTER
ÉMETTEUR BLUETOOTH
TRANSMISOR BLUETOOTH
AA-T100BT -J/C
© 2007 Victor Company of Japan, Limited
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that 
may cause undesired operation.
CAUTION: Changes or modifications not approved by JVC could void user’s 
authority to operate the equipment.
Contact
Address: JVC 
AMERICAS 
CORP.
 
JVC COMPANY OF AMERICA
 
1700 Valley Road, Wayne, N.J. 07470
Telephone:  1 (800) 252-5722
Note: This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with the 
instructions, it may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of the 
following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
IC INFORMATION
This device complies with RSS-210 of the IC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that 
may cause undesired operation of the device.
CAUTION: Changes or modifications not approved by JVC could void user’s 
authority to operate the equipment.
Contact
Address: 
JVC CANADA INC.
 
21 Finchdene Square, Toronto, ON M1X 1A7
Telephone: (416) 293-1311
e-mail: info@jvc.ca
Note: This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to Industry Canada’s RSS-210. These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with the 
instructions, it may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of the 
following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
INFORMATION SUR IC
Cet appareil est conforme à la RSS-210 du réglement de la IC. Le fonctionnement 
est sujet aux deux conditions suivantes:
(1) Cet appareil ne peut causer d’interférences nuisi-bles
(2) Cet appareil reçoit toute interférence même les interférences qui peuvent 
occasioner un mauvais fonctionnement.
ATTENTION: Les changements ou les modifications non approuvés par JVC 
risquent de retirer à l’utilisateur le droit d’utiliser l’appareil.
Contact
Adresse: 
JVC CANADA INC.
 
21 Finchdene Square, Toronto, ON M1X 1A7
Téléphone: (416) 293-1311
e-mail: info@jvc.ca
Remarque: L’appareil a été testé et jugé conforme aux limites des appareils 
numériques de classe B, aux termes de la réglementation RSS-210 de l’industrie 
du Canada. Ces limites ont pour but d’assurer une protection raisonnable contre 
les interférences parasites lorsque l’appareil est utilisé dans une installation 
résidentielle. Cet appareil engendre, utilise et peut émettre une énergie 
radioélectrique et, s’il n’est pas installé et utilisé en stricte conformité avec ces 
instructions, il peut provoquer des interférences parasites dans les liaisons 
radiophoniques. Ceci ne garantit pas pour autant qu’une installation particulière 
n’émettra aucune interférence. Si l’appareil engendre des interférences parasites 
avec la réception radio ou télévision, ce qui pourra être déterminé en éteignant 
puis en rallumant l’appareil, il est conseillé à l’utilisateur d’essayer de corriger les 
interférences en prenant l’une des mesures ci-dessous:
•  Modifier l’orientation ou changer l’emplacement de l’antenne de réception.
•  Eloigner davantage l’appareil du récepteur.
•  Brancher l’appareil dans une prise d’un circuit différent de celui auquel le 
récepteur est raccordé.
•  Demander l’aide de son agent ou d’un technicien radio/télévision qualifié.
ENGLISH
This product’s performance would be degraded under a strong electro-static 
environment. And the function would be self-recoverable after the above case.
This product’s performance would be degraded since the disturbance from the mains 
cord. And the function would be self-recoverable after the above case.
FRANÇAIS
Les performances de ce produit se détérioreront dans un environnement fortement 
électro-statique. Par ailleurs, le fonctionnement se restaurera de lui-même dans le 
cas ci-dessus.
Les performances de ce produit se détérioreront en cas de perturbations du cordon 
d’alimentation. Par ailleurs, le fonctionnement se restaurera de lui-même dans le cas 
ci-dessus.
ESPAÑOL
El rendimiento de este producto puede deteriorarse en un entorno con campos 
electrostáticos fuertes. El funcionamiento se repondrá a la normalidad después del 
caso arriba mencionado.
El rendimiento de este producto puede deteriorarse debido a las perturbaciones del 
cable de la red eléctrica. El funcionamiento se repondrá a la normalidad después del 
caso arriba mencionado.
LED flashing patterns
Status
LED
Flashing pattern
Pairing
Blue
●-●-●-●-●-●-●-●-●-●-●-●-●-
Waiting connection
Blue
●-●-●--------------●-●-●----------
Last device connecting
Blue
●-●-----------------●-●-------------
Communicating
Blue
●---------------------●-----------------
4. To protect the transmitter, DO NOT…
●  allow them to get wet
●  shake them or drop them against hard 
objects
●  insert forcibly when connecting the unit; 
otherwise the unit and the connected 
device may be damaged.
●  apply excessive force to the unit when 
connected; otherwise the unit and the 
connected device may be damaged.
●  touch the terminals of the unit and the 
connected device or contact metallic 
object to them; otherwise damage or 
malfunction may be caused with poor 
contact or a static shock.
5. About iPod…
●  If the iPod does not play correctly, please 
update your iPod software to the latest 
version. For details about updating your 
iPod, check on the Apple web site.
<http://www.apple.com>
●  Sound distortion may occur when playing 
back audio source with high recording 
levels. When distortion occurs, it is 
recommended to turn off the equalizer of 
the iPod. For information on operating 
the iPod, see the iPod instruction manual.
●  JVC is not responsible for any loss of or 
damage to iPod that might result from 
the use of this product.
English
Thank you for purchasing this JVC product. Before you begin operating this unit, please read 
the operating instructions carefully to be sure you get the best possible performance. If you have 
any questions, consult your JVC dealer.
CAUTION
Features
This unit is a stereo transmitter using Bluetooth® wireless technology.
Power supply:
supplied from iPod
Battery life**:
up to 6 hours (iPod nano 2nd generation)
** Depends on use or the type of the iPod 
connected
Mass:
6 g (0.21 oz.)
● iPod is a trademark of Apple Inc., registered 
in the U.S. and other countries.
● The Bluetooth® word mark and logos are 
registered trademarks owned by Bluetooth 
SIG, Inc. and any use of such marks by Victor 
Company of Japan, Limited (JVC) is under 
license. Other trademarks and trade names 
are those of their respective owners.
•  The pass code* of the unit is set to “0000.” If the pass code of the target Bluetooth device is 
other than “0000,” you cannot execute pairing. When the target device requests the pass code 
during pairing operation, enter “0000.”
* also called as “pass key,” “PIN number,” etc.
•  The pairing mode will be canceled about in 60 seconds. In this case, turn off the iPod and 
disconnect the unit, and then perform the pairing operation again.
1.  For your safety…
●  Never use the headphones when driving 
a car, motorcycle, or bicycle. This could 
result in an accident. 
●  Pay special attention to traffic around 
you when using the headphones outside. 
Failure to do so could result in an 
accident.
●  Be careful not to turn up the sound 
volume too high. Your hearing can 
be damaged by listening to sounds at 
excessive volume for long periods.
●  Do not disassemble or modify the 
transmitter.
●  Do not allow flammable, water or 
metallic objects to enter the transmitter.
●  In the dry air such as in winter, you 
may feel a static shock when using the 
transmitter.
2.  Avoid using the transmitter…
●  in places subject to excessive humidity or 
dust
●  in places subject to extremely high (over 
40°C or 104°F) or low  (under 0°C or 
32°F) temperatures
3.  DO NOT leave the transmitter…
●  exposed to direct sunlight
●  near a heater
About Bluetooth
Bluetooth is a short-range wireless radio 
communication technology for the mobile 
device such as cellular phones, portable PCs, 
and other devices. The Bluetooth devices can 
be connected without cables and communicate 
each other.
About Bluetooth Profile
Bluetooth Profile designates the way of 
communication between Bluetooth devices. 
The system supports the following Bluetooth 
Profiles.
A2DP: Advanced Audio Distribution Profile
The profile controls sending/receiving the high-
quality audio contents.
AVRCP: Audio/Video Remote Control Profile
The profile controls the functions of audio/
video devices such as playing, stopping, pausing 
and volume control.
About pairing
Pairing creates a unique and encrypted link 
between two Bluetooth devices and lets them 
communicate with each other. Bluetooth devices 
will not work if the devices have not been paired.
Cautions on Bluetooth 
communication
• Microwaves emitted from Bluetooth devices 
may affect the operation of electronic 
medical devices. Turn off this unit and other 
Bluetooth devices in hospitals, airplanes, 
trains, or crowding places.
•  Bluetooth devices use 2.4 GHz band, which 
is the same as that used by wireless LAN 
devices and microwave oven. Interference 
may occur near these devices and cause 
noise, disconnectivity, or a decrease of 
communication speed.
•  Connection with all Bluetooth devices cannot 
be guaranteed. Connectivity, operation, 
display indication or function may differ 
depending on the characteristics and 
specification of the devices.
• Some Bluetooth devices take more time to 
establish connection.
•  To use the Bluetooth functions, the Bluetooth 
devices are required to be compatible with 
the same Bluetooth profiles as this unit is. 
However, the functions may not be available 
depending on the specifications of the 
Bluetooth device even when it is compatible 
with the same profiles.
Parts name
Compatible iPods
● iPod (with click wheel, with color 
display, with video)
● iPod classic
● iPod touch
● iPod mini
● iPod nano (1st, 2nd, 3rd generation)
•  Do not connect the unit to devices 
other than above. Otherwise, 
malfunctions may occur on the unit or 
the devices.
•  This unit does not support iPod 3rd 
generation or earlier.
Registering to a Bluetooth device – Pairing
Before pairing...
•  Turn off the iPod.
•  Place the target Bluetooth device within 1 m 
of the unit.
1  Turn on the target Bluetooth 
device and execute pairing 
operation on the device to find 
the unit.
2  Connect the unit to the dock 
connector on the bottom of the 
iPod, then turn on the iPod.
The unit automatically starts pairing and 
the LED indicator flashes rapidly. When 
the pairing is completed, flash will become 
slower after the pairing completed.
Listening to Music
Preparation: 
•  Finish pairing between the unit and the 
Bluetooth device.
1  Turn on the Bluetooth device.
2  Connect the unit to the dock 
connector on the bottom of the 
iPod, then turn on the iPod.
The unit automatically turns on and will 
connect to the target Bluetooth device.
•  If the connection is not completed within 
five minutes, the unit automatically turns 
off. In this case, turn off the iPod and 
disconnect the unit, and then repeat the 
procedure from step 1.
3  Start playback of the iPod.
Refer to the iPod’s instruction manual for 
the operation of the iPod.
•  If the target Bluetooth device supports 
the AVRCP of the Bluetooth Profile, 
play, pause and skip (forward/reverse) 
functions are available from the target 
Bluetooth device.
To stop using the unit, 
Turn off the iPod and pull off the unit straight 
from the iPod.
Troubleshooting
What appears to be trouble is not always 
serious. Check the following points before 
consult your JVC dealer.
Cannot pair the devices.
☞ You cannot pair the Bluetooth device having 
sending function only.
☞ Bring the devices as closer as possible.
Cannot connect the devices.
☞ Pairing is incomplete. Perform the pairing 
again.
The sound is intermittent/The 
communication range is small.
☞ Although Bluetooth
®
 wireless technology 
can transmit the contents within the range 
of approx. 10 m, obstacles (human bodies, 
metallic objects, wall, etc.) or radiowave 
condition may affect the sound and decrease 
its range.
☞ The sound may be intermittent in the 
following cases. Avoid the following 
conditions when you use this unit.
–  Places where the wireless local area 
network is applied.
–  Near the microwave oven.
–  Near the other Bluetooth devices.
–  Places where the radiowave is used.
No sound.
☞ The connection between the Bluetooth device 
and this unit is incomplete. Connect the 
devices again.
Specifications
Designs and specifications are subject to change without notice.
Compatible iPods:
iPod (with click wheel, with color display, with 
video), iPod classic, iPod touch, iPod mini, iPod 
nano (1st, 2nd, 3rd generation)
Bluetooth version:
Bluetooth 2.0 certified
Output power:
Bluetooth power class 2
Service area:
max. 10 m (10.9 yd.)*
*  Communication range may vary depending 
on the environmental conditions.
Frequency band:
2.4 GHz (2.4000 GHz - 2.4835 GHz) 
Bluetooth profile:
A2DP (Advanced Audio Distribution Profile) 
AVRCP (Audio/Video Remote Control Profile)
Supported Codec:
SBC (Subband Codec)
Printed in China
LNT0097-001A
Music
Control
with iPod
Optional (not included) Bluetooth 
Stereo Headset
HA-W700BT
Bluetooth receiver with 
audio streaming function
Connection with all Bluetooth devices cannot be 
guaranteed.
iPod Connection 
terminal
LED indicator
BT_transmitter_J/C_3.indd   1
BT_transmitter_J/C_3.indd   1
2007.10.15   10:32:15 AM
2007.10.15   10:32:15 AM